Marelli Iaw 8F.5T Help Address

[Metropolis]

Hi guys, as the driver of the ECM I don't trust to nothing, and some of the maps seem to me at how awkward I ask for help to you in this endeavor to understand a p? the maps in this Ecu even if very dated.
However, by uploading the file in the Ecm there are maps in the negative, even, and I don't understand that even if CME me, the door to the maps injection...I enclose the engine map read even though I have no doubt that it ? read in the correct way, why? the willem returned me to the pi? Cecksum different on the pi? reading.Thanks to allReading 4.rar

[et600]

Hi guys, as the driver of the ECM I don't trust to nothing, and some of the maps seem to me at how awkward I ask for help to you in this endeavor to understand a p? the maps in this Ecu even if very dated.
However, by uploading the file in the Ecm there are maps in the negative, even, and I don't understand that even if CME me, the door to the maps injection...I enclose the engine map read even though I have no doubt that it ? read in the correct way, why? the willem returned me to the pi? Cecksum different on the pi? reading.Thanks to allReading 4.rar

Hello, On these ecu a little bit of experience with me are done, compare the various bin that reads the willem and if comparing with the ecm you d? the curves are all different and you have some problem with the player. A piece of advice that I can give ? to purchase an emulator, I use the ostrich 2.0 using free software so that you can go to see where your ecu will read the various addresses while you are in gear and you can change them in real time. Thanks to him I managed to find several nice maps such as the management of the enrichment on the basis of water temperature, etc, etc

[Metropolis]

Uhmmm Good azzo, can you tell me where can I get it? I find all of sellers of foreign and I'm afraid I don't trust...

[et600]

Uhmmm Good azzo, can you tell me where can I get it? I find all of sellers of foreign and I'm afraid I don't trust...

unfortunately ? only available in america, I bought it from l?, it's worth the expense, even why? it makes all the old units with the eprom 27c***

[et600]

Hi guys, as the driver of the ECM I don't trust to nothing, and some of the maps seem to me at how awkward I ask for help to you in this endeavor to understand a p? the maps in this Ecu even if very dated.
However, by uploading the file in the Ecm there are maps in the negative, even, and I don't understand that even if CME me, the door to the maps injection...I enclose the engine map read even though I have no doubt that it ? read in the correct way, why? the willem returned me to the pi? Cecksum different on the pi? reading.Thanks to allReading 4.rar

However, for the record, that the control unit of the checksum didn't give a shit, nothing max could settarti the error in diagnosis, but should not turn on the light in the injectors

[Metropolis]

Then also Point Gt is good very good...I have to see a little? if the expenditure, should I do it or not...

[et600]

Then also Point Gt is good very good...I have to see a little? if the expenditure, should I do it or not...

you should do it, I've never used it for this car.
Among other things, for the gt, on the site of the sw tunerpro, c'? the "driver" for the car, but do not ? said that is correct.

[Metropolis]

et600 since we're here can I ask you if you can give me the real matrix of the injection? the curse I have a small problem at full load and I can't seem to gain weight at that point the driver of the ecm they suck because they are all wrong...

[djole]

good files

[LL205gti]

Interesting discussion.
I also use the ostrich 2.0 but I could not find much.
et600 which maps were you able to find? how did you find them?

thanks.good forum.