reading BDM edc16u31 cock v54 not part

[bmw320cd]

Hello, open your tool and see if you have components that give the problem to reading bdm.......

you lighthouse photos as soon as possible of the cock is open...so let's see what's there in

I've seen your photos, but I remember (I have verified I am writing in speed..) that used 6 pitches, not 5 as you have on the bosch,not ? that you have a e xxx wrong... check on the documents of the rooster...

in the manual of the rooster pdf that I have given in the cd, ce written for the bosch should be used 10 pitches,in this way ("or" = free "x" = pin)

or or x x x x x

or or x x x x x

5(x)+5(x)= 10-pin welded on the e xxx....

that power supply uses the test with a higher amperage

use the power of the cock in hotel... by a pc with the usb cable, I see a voltage 12.8 v, while the pin 12v of the e xxx bosch arrive 11,85 v...I also tried with a stabilized power supply , but nothing changes, always error, I recognize the flash....

not ? you put skedino adapter to the contrary, the written cmd goes to the skedino

here we attached photo with the writing of how to use the CMD, and the e xxx and flat cables

it is possible that the tool nn good anyway, try also to change from 3.3 v to 5.0

also tried but without result....

[Exelion1986]

the other day I read my that ? a MED 9.1 but the address should be the same
my e xxx has the pin cos? and has not given problems

o o x x x o x
o o x x x o x

hoping that it is the interface if the law could be various things
the pin will not touch the good, but difficult, given that these for bosch are big, me ? success with the marelli that they are small and you cannot see well
incorrect links in various ways
for example to me the other day not the read ? was the first bosch I did
attack my power supply to the e xxx, the led turns on, then it should be all ok, but nothing
then I discovered that I was feeding to the contrary, why? I cut the cables to the power supply and I put a plug of white, as the cords of the rooster, only that others are reversed with respect to this
you got to take a picture of all connected?
however, 3.3 V, I don't think it's a good idea to play with the voltages

[massimiliano83]

once you open the soft do the procedure by choosing the bdm procedure if when you open the strovi gi? checked a few times nn

[bmw320cd]

the other day I read my that ? a MED 9.1 but the address should be the same
my e xxx has the pin cos? and has not given problems

o o x x x o x
o o x x x o x

hoping that it is the interface if the law could be various things
the pin will not touch the good, but difficult, given that these for bosch are big, me ? success with the marelli that they are small and you cannot see well
incorrect links in various ways
for example to me the other day not the read ? was the first bosch I did
attack my power supply to the e xxx, the led turns on, then it should be all ok, but nothing
then I discovered that I was feeding to the contrary, why? I cut the cables to the power supply and I put a plug of white, as the cords of the rooster, only that others are reversed with respect to this
you got to take a picture of all connected?
however, 3.3 V, I don't think it's a good idea to play with the voltages

in the manual of my cock,to be used for the pin as I have written above,that in this way

or or x x x x x

or or x x x x x

the photo with everything connected I had already attached... you riallego here

once you open the soft do the procedure by choosing the bdm procedure if when you open the strovi gi? checked a few times nn

you tried several times,even bdm jtag , but nothing... and selected every time I open the software...

[dvdtuning]

But, you get the power? on the e xxx intermediate where there are two flat and the power supply, the red led lights up? that gives you the error?

[bmw320cd]

But, you get the power? on the e xxx intermediate where there are two flat and the power supply, the red led lights up? that gives you the error?

my e xxx has no led... anyway here comes the power,because on the e xxx bosch, in the pin +12v with the tester, I measure 12v,then the current arrives...
me from eprom not supported

[silven]

I checked in my instructions of the cock that I enclose... he says to use 6 pitches... my ? so...New immagine.jpg

[bmw320cd]

I checked in my instructions of the cock that I enclose... he says to use 6 pitches... my ? so...New immagine.jpg

I can't see the attached images....

[passione motori]

I can't see the attached images....

Bmw, you lose 2 minutes open your tool and locate the components dedicated to the bdm, if your tool find ls14 do not waste time simply and contralla also other parts will surely be replaced....

[passione motori]

Bmw, you lose 2 minutes open your tool and locate the components dedicated to the bdm, if your tool find ls14 do not waste time simply and contralla also other parts will surely be replaced....

check.....? now to rest I'm struggling with the keyboard.