map injection times edc15c7

[gionag]

I sent the map to the maximum value and today I definitively removed from the machine by putting a resistor 33 ohm 5 watt cos? I kiuso well as the hole from the collectors of cast iron.... Another thing I did was remove the recycling of the oil vapours, I put a nice tube that goes to the ground cos? my beautiful pressure sensor remains clean and Pinto

ocio to disconnect the hose of the vapors... I think so? do not put negative pressure on the block... what ? good thing ? right...
risks of leaks are the worst if not worse...
use a decanter in series on the line, rather than a disconnection in total.

the heat exchanger you have it deleted ? if s? as you have bypassed the circuit of the liquid ? I have bent an aluminum tube cos? to fake it...

[fabio]

The heat exchanger is still not l I deleted but it will be doing? when I remove the perch? so do not bother and do not urge to do it... For the decanter, I know that we want to, and I had made the drawing of how to do it but I see many engines, even with a good cavalry, which not the Mountain, and walk the same... And to be honest with you today from my parts it rained and I immediately thought of the tube ****** and all humidity? that would have been able to enter in the cover the tips and I felt guilty as soon as I can, I attempt in the making, hoping to not run into too many problems

[gionag]

... bought for a few euros should lose the time to do so ?

[fabio]

That you want to short the euro? I know that you spend at least 50 euros... I rather me do it, it's free..

[gionag]

That you want to short the euro? I know that you spend at least 50 euros... I rather me do it, it's free..

they are in a position asian in very less... and are the same that sell in italy in the 50 odd euros... take a ride
anyway.. I agree with you that costruirsele these things d? a certain amount of satisfaction and dependence.

... (we are going OT )

[fabio]

Then, the geometry moves very easily with a screwdriver and it does not seem blocked, the pressure sensor and clean, only the controls with the vacuum gauge I have not done... having Said this I have adjusted the map with the files that I have given you, and the result ? was a pressure pi? constant, but a peak exaggerated ( almost 2 bar) for a short time and just thrust the pedal... as soon as I can I attach the video of the gauge if needed

[gionag]

Then, the geometry moves very easily with a screwdriver and it does not seem blocked, the pressure sensor and clean, only the controls with the vacuum gauge I have not done... having Said this I have adjusted the map with the files that I have given you, and the result ? was a pressure pi? constant, but a peak exaggerated ( almost 2 bar) for a short time and just thrust the pedal... as soon as I can I attach the video of the gauge if needed

The video ? always welcome, even if only to see the pressure without being able to match other data (rpm, qi,%, actuator, etc.) has little sense
I generally start out with that system, then I'm going to see where the pressure decreases to or exceeds the desired, and put in relation to the % of the valve... it is obvious that if you push more? diesel also iq ir? low
(the cio?... iq on the corresponding bp) then you should adjust even in the other columns, not just the terminal.

now that I can, I'd be curious to see your map, cos? maybe we learn together...

[fabio]

Yesterday I tried the pi? times to upload the video but I know that ? a bit large, as soon as I get home I try to compress it, and I am attaching the map (I know already? you impressionerai when you see it XD)

[gionag]

not if it is legitimate, but perhaps a link to youtube would be better...
I fear that the attachment size is too strict... and calculates the video ? gi? compressed to its nature, then by zipping them/rarrandolo will change? little or nothing...

[fabio]

link deletedhere is the link ...and here is the map 147mod7.rar ...there are still things to do but unfortunately ? come the summer and I work in a food industry 12-13 hours a day, so I only have the time to sleep XD , let me know what you think