kess v2 or fgtech galletto v2?

[vicfurpac]

Hi guys, sorry for the umpteenth my question. But before doing the steps wrong, I prefer to always ask.I in addition to cars, I would need to remap two tractors, a dear friend of mine, specifically of the New Holland Ts125. I read from the site of alientech that the kess v2 is doing it, now I don't know if the clone does the same, what do you think? What do you advise me kess v2 clone or fgtech galletto?
Thanks a lot in advance

Hello. Kess v2 clone, I believe, not just cars. Kess v2 original is traucks, tracktor, marine, but, ? need to buy protocols and are expensive.
FGTech clone, instead, the tractors, but only the ones listed on FGTech.

guys but back to the cock...what do you recommend as my first purchase from beginner, v52, which is very easily in italy or the v53 that very probably will have to? order it from some chinese website?

text moderate why? written in English

as always, I say better the v53 chinese from all points of view

The only problem so far was the installation of the software with v53

Sorry , but since I read so many messages (pu? be that someone for me ? escaped) in which all I ask is which ? the right one and which is not , in the pi? I answer my work very well ? a matter of luck ..... but you could make a nice discussion where the luck we try to limit it even why? however, when you talk about bad luck when you throw money , I was wondering if the Lucky ones could post a picture of the hardware , possibly if visible and readable even the abbreviations of the major chip .
I think that by doing so perhaps we limit a p? the unlucky ones (like me) .

Thanks

I would like to send you some files for me to work with FGTech but I have not yet reached the 80 messages.

[ciullo.eugenio]

but the installation does not ? difficult, just direct the install on the drivers and the game ? done... no ? difficult

[meccanico 85]

Hello everyone I am a new member. I was unsure of what to buy x map but now that I have read all your forum are more confused still. I'm starting now and I want to make a basic course and buy a clone that is more suited to my needs, i.e. no fap no egr scodifiche, change any of the map to drive the most common ford fiat opel peuget, etc for both gasoline and diesel what do you advise me please help me

Sorry if I've completed my presentation. As I wrote before, my name is gaetano the game, I have 29 years of leonforte (en) are a mechanic for more than 14 years, I am writing to this forum because I think that it is important for me and I can serve in the future, however, I must say that you are prepared and humble ciaooo

[ciullo.eugenio]

Hello everyone I am a new member. I was unsure of what to buy x map but now that I have read all your forum are more confused still. I'm starting now and I want to make a basic course and buy a clone that is more suited to my needs, i.e. no fap no egr scodifiche, change any of the map to drive the most common ford fiat opel peuget, etc for both gasoline and diesel what do you advise me please help me

Take the fg tech v53 like ? was recommended to me

[ugoboss]

Hello everyone I am a new member. I was unsure of what to buy x map but now that I have read all your forum are more confused still. I'm starting now and I want to make a basic course and buy a clone that is more suited to my needs, i.e. no fap no egr scodifiche, change any of the map to drive the most common ford fiat opel peuget, etc for both gasoline and diesel what do you advise me please help me

the interface that you have suggested is fine, but remember that only serves to read and write a lot ecu, to do the jobs that you say "no fap egr scodifiche and edit maps", then you'll need to do the interface does absolutely of these jobs, you have to edit the files, or you have to lean on someone doing it for you.

[meccanico 85]

I understand but the better kess or fg tech v53'm always x the clone which is the most simple and the most complete

[ciullo.eugenio]

I understand but the better kess or fg tech v53'm always x the clone which is the most simple and the most complete

Not c? a simple and a easy, you only need to read and write the procedure ? at the same, for the matter of completeness ? was recommended the most? times reading this discussion, the fg tech v53 why? ? the pi? complete and offers more? chance? seen that d? the possibility? to use jtag, read around the topic to find the answer

[vicfurpac]

I understand but the better kess or fg tech v53'm always x the clone which is the most simple and the most complete

Clone Kess v2 is pi? vehicles that Fgtech as they are listed in their computers , is also a pi? checksum , but clone Kess v2 car OBD as they are enabled, other protocols. You would need to get KTag clone to do BDM , Boot , Jtag , etc., but once again KTag clone just makes the car as they are enabled, other protocols. On the other hand , I would say that FGTech v52 and v53 are the best solution how long to make? all of the OBD , BDM , Boot, Tricore , Jtag , but always use caution, as it is a clone tool and there are many l? out . I recommend to look for which both pi? manufactured as there are certain that the PCB board and soldering of the components are poor , and more? the chinese like to grind the identification of the integrated circuits off sometimes damage the circuits. I decide to buy a FGTech clone , be sure to know that ? feedback and after the purchase , open the case, only to check if all the components inside have been damaged with the grinding chinese or poor welding as I had a Fgtech who started to smoke after I turned on due to the bad connection of the poor welding.

[ciullo.eugenio]

are the things that can happen, as I say, I c'? always a chinese fregher? the system anyway, you are right... always best to check the welds, before the damage is done