bmw 635d 286hp dpf/cat removed x expert

[tonyteam]

hello all, preferring the map in the right way, I tried to map the drive.
previously with 20% on the timing of injection did not smoke, was strong (337cv) and with a boost in the diagnosis of about 2.1-2,2bar , even if a little dancer walked enough.
given that I would like to map it in the right way I did I'm file..I don't think he forgot something, however, it should be less, I don't know if injected, really...I'm afraid that there is something else to limitare. x if it means I can give a hand?

51 visits no answer? I know that here people download and if it is as well to shut up...

[msport (exil77grande)]

have just downloaded 5 times,maybe those who download does not know what to say or has no advice or maybe download only study from my hand, I will say that it's not a method I used, because in a classical way if you know what to do go very much better and stronger,I have a 330d e90 231cv and I have done several tests.

[tonyteam]

thanks msport, I'm glad that there is someone in my situation...in your you have also removed the FAP with a dtc error?

riaggiorno the rear are returned in line with the performance of before, even with the dis I still don't understand where you can find the mg for the IQ, when I can only find water temperature,discharge, pressure rail and the turbo mass air flow sensor.
to test, I raised the IQ limiters that should be already? in mg and not mm3. in your opinion, I am injecting what I wrote in the map nm to iq? why? it seems to me quite a bit 88mg and over, and I was expecting or + hp or + smoke...if my reasoning ? valid + 82mg (100mm3) do not inject why? ? the fact that the last value of the bp in the map of the injection timing (duration)

all those lim, which I have set to 8500 and 9000 han sense to put them so? or just enough to set them to the 8200?

no one can give me a hand?

I found other lim, I think iq place the map, hoping that some good soul will face alive

[tidus1985]

I download, tomorrow when I come back from work the control and I give you a hand for that that I can

from an eye, I had a little surge, but I have not touched another

rightly, you can't download the file, tomorrow we'll place the addresses of the limiters that I found

[tonyteam]

ok, I am curious to see what limiters you have found...

I write the addresses I found for the iq limiter ..maybe are the same that you have found you tidus! 2 iq limiter (0C7D0A and 0ED03A) + 1 torque limiter 0CF15C (should depend on the EGT ), cos? say in various forums.

[tidus1985]

OC7CFC Should be a torque limiter, OCEEDC and later, OCF028 would seem to be a limiter, diesel, and also the following, OD9FF8 another limiter, 0DE5F= and the next would seem limiters, diesel, 0ED01C ? undoubtedly, a limiter, diesel, 0EDCA6 the same, for now I found these

[tonyteam]

thanks tidus for your contribution. I wonder why? with 80 messages, I can't download manco an attachment again..bho

[tidus1985]

brings patience, you will see that you will be enabled, I have come to 100 messages without even realizing it!

[tonyteam]

which address did you mean tidus with 0DE5F= ...then 0edca6 has values of 8192 cio? 100% throttle, how do you know that ? an iq limiter?

[Ilmerca]

I can't download the maps posted in this car there are 4 torque limiters from moddare important the rest...... with a few things without dpf arrive comfortably to 350 horses. The turbo 2.2 not ? diagnosis gives you the value, not real. Put a pressure gauge True that ? better.