map yaris d4-d

[ingmodena]

Hello all, after the purchase of the rooster v2 on the site, I have ventured on my first map (toyota yaris d-4d) and I would like to ask you about some doubts that I have:
1) to change the map serves a specific programme type ECM? I used this but I have not found the correct driver, I found one with number, HW is the same but the number of SW ? different ? a problem? where can i find a driver that I miss?
2) I do not ? appeared in the menu "Turbo", perhaps it depends on the drivers that do not ? it is the right one?
3) I changed some of the maps, could you tell me if they make sense to you?
Thanks a lot

[munro]

the number of hw or sw other than pu? create problems with the cks but and remedied with the rooster if I'm not mistaken...
maps turbo it can't find why this car has a turbine fixed not managed by the ecu...
for? in the drivers and conseguena in the map many maps important that you have not changed first of all the map pedal that if I'm not mistaken starts to 077BD2 and ends at 077C9A is missing the map rail and its limiter, and a bunch of other things
as to the mod real when I saw the lim couple, and I'm scared.....you started with 800 rpm with an increase of 60% and beyond...to 1000 rpm, you are more than 100% increase and at 4,200 rpm, close with the 176% increase....I guess that's not okay.....
the rest can be improved, especially in the times...and you have to adapt the lim fumes...first for? ask if the address that I have posted corresponds to the map the pedal and rifalla starting with l?.....

[ingmodena]

Hi Munro, thank you for your advice. I have reviewed the 2 maps injection zoned and, in particular, the torque limiter, do you think it will go cos??
The map of pedal I don't see it in the menus, in these cases, how does that work? I have to look up the range of addresses that I have indicated in the tables hexadecimal? Then the change is on the 2d graph on each address? Can you tell me how?
Thanks a lot

[munro]

[?QUOTE=ingmodena;30501]Hello Munro, thank you for your advice. I have reviewed the 2 maps injection zoned and, in particular, the torque limiter, do you think it will go cos??
Then In there you're very own...in the file I see that this time you touched only one of the 6 maps of the injection times and the torque limiter and was put back ori...
if it touches only one of all 6 of the maps times the force of things you have to do them all the same way..is how the area changed that as increases...for now I would tell you to let the stre maps time and focus on the maps pedal lim torque and map the fumes...already touching these three adapting to request restriction, you'll hear a substantial improvement.....
The map of pedal I don't see it in the menus, in these cases, how does that work? I need to search for l?the range of addresses that I have indicated in the tables hexadecimal? Then the change is on the 2d graph on each address? Can you tell me how?the map of pedal cannot find it in the menu, why ? out driver cio? ecm is not the ripota between those editable by himself..then you should create a driver....starting from those addresses that I gave you referred to? you should ask for confirmation to others more experienced than me....
Thanks a lot[/QUOTE]
below we transcribe the addresses in your file that gives you the ecm but with the actual naming(I think....you have to ask for confirmation)
076DB2=torque limiter(in this case the name ? right)in this map, the values read in the various breakpoints are directly the iq of diesel in mm3(this and from the name itself, a map of the limitation of the iq that goes appropriate to that request..cio? the map of pedal or Driver's Wish)
07B21A=injection correction:in this case the ecm the name l? has failed...this ? the map rail but since we do not know where is the limiter for the moment, don't change it...
072B34-078BA6-079366-072F14-078F86-079746: really? these are all maps of the injection time that the ecm calls with the names of the more bizarre..here is the speech that I wrote to you a moment ago...
076E2C=injection split:in truth? this map ? the limiter flue gas and in the axes in 2d you have on the x-axis the speed of up to 4800 and on the y-axis the quantity of air sucked in and weighed by the maf that goes from a minimum of 200mg of up to 700mg...in the z-axis of this map you have the iq that the ecu must comply with in order to have a given stoichiometric ratio to avoid smoking..so if you e.g. split the amount? air of a certain bp of the y-axis with the iq of another bp of the z-axis you get a afr to understand if e.g. split 700mg of the air to 33 mm3 of diesel you hang out at a ratio afr.....attention to? as you may have noticed, I don't l? calculated for you this afr because you can't? calculate with two units? measuring different right???(mg x mm3) so you have to convert the iq of diesel from mm3 to mg by multiplying this iq by 0.85..so in the case of the first 33 x 0,85=28,05 mg
now, given that the unit? measures are the same you can? calculate our afr reported in the map and then 700/28,05=24,95 of afr...(remember uqesti are random numbers) the rule imporebbe to calculate for all the boxes of the map, the fumes, the value of the afr so you know where you can? push with the increase in diesel fuel and, consequently, with the lowering of the ratio afr adapting this map of limitation to our map request(map pedal)...but many of the calculator, do not want to use and then usually damage increases(for*******m I would say)of 7% in this map.....you act as you see fit...
finally 077BE6 starts the Z-axis of the map the pedal to where you post it to the complete address in the other post, and you should ask for confirmation...***** and you may have realized this map with the pedal ? the main map where the ecu gives the order to the diesel you ask for with the pedal first? this request will be limited by the various maps described above....
I hope you have been all of the help..

[ingmodena]

Sorry, I just noticed that I posted 2 files for error, the last version that I wanted to see ? the one above from 264,2 Kb. Someone can? help me by answering my questions? Thanks

[ingmodena]

thank you for your long and detailed explanation
I tried to create the driver to map the pedal doing the Edit -> custom Drivers, and writing the address from which you should start drinking ? 077BD2 or 077BE6?) but the numbers that come out in the table does not think they are right... there are several zeros and numbers are very high...
can you tell me if I'm wrong, the procedure of the creation of the driver, or if I'm wrong, the starting address?

[Team elettronica]

just coming to the 80 messages I get everything and if I can I'll give you a hand