Opel vivaro 1.9 dt egr problem

[michele30]

Yep, I have a little big problem with this means, about a month ago ? changed l egr ( I have to say that the engine in question ? the 19 tdiesel of renault and the middle ? a 2002 year ) tornado to the problem ? arrived with lamp on-and-error p0400 cio? egr valve, valve changed and that is it.
Back after a month with light that had eccesa on the highway and always error on the egr.
The put but trying it ? also very slow in the beginning, up to about 2800 rpm in the turbo ? entered ? as firm as if it were the egr valve maybe a bit open, but not ?.
There ? for the case never happened something similar?

[zullo]

happened to me and on a scenic 1.9 as well was closed gave me problems not accelerating slow start turbine that is not pushing black smoke at will
the deleted and put a strip of sheet
he is still walking as I would recommend you to do according to me.

[motorsport]

happened to me and on a scenic 1.9 as well was closed gave me problems not accelerating slow start turbine that is not pushing black smoke at will
the deleted and put a strip of sheet
he is still walking as I would recommend you to do according to me.

and the best solution!!!!!

[michele30]

this is a non-smoker but' ? just a little slow in the beginning and it takes me this error.
where did you put the plate?

[zullo]

this is a non-smoker but' ? just a little slow in the beginning and it takes me this error.
where did you put the plate?

where are you going to finish the tube from the exhaust manifold and goes under the egr valve
or loose the flancia and or put a small plate in the middle between the pipe and egr valve

[carlo abarth]

you may find that the valve goes up when it goes into turbo that does not maintain the kiusura ..try tapparla and try!!!!!

where are you going to finish the tube from the exhaust manifold and goes under the egr valve
or loose the flancia and or put a small plate in the middle between the pipe and egr valve

[IlCurioso]

I don't know the mileage of the vehicle but on Iveco vans, it happens that you "incaccola" around the intake manifold and inside the various air passages become clogged, causing precisely the same failure! Now I do not know if ? the same for the vivaro but maybe if not ? difficult maybe with a video camera tries to throw an eye!

[michele30]

I try to tapparla and see what comes out tomorrow. if I find where to put the plate, will update...
thanks

I did a test by putting a sheet on the pipe that goes to the valve, but with 3 holes by 5mm the middle of not ? changed nothing, the only thing ? now as the error always p0400 but instead of being excessive ? little and in fact does not erase it.
However, the means should not be just the way it should go, even so, can you please tell me when should measure the mass of air to the max?
I know that the minimum amount of heat must be from 35 to 47, and here we are, but at the max only comes to about 250, it seems a little bit on the 3500 rpm is so low

[carlo abarth]

then the result????

I try to tapparla and see what comes out tomorrow. if I find where to put the plate, will update...
thanks

I did a test by putting a sheet on the pipe that goes to the valve, but with 3 holes by 5mm the middle of not ? changed nothing, the only thing ? now as the error always p0400 but instead of being excessive ? little and in fact does not erase it.
However, the means should not be just the way it should go, even so, can you please tell me when should measure the mass of air to the max?
I know that the minimum amount of heat must be from 35 to 47, and here we are, but at the max only comes to about 250, it seems a little bit on the 3500 rpm is so low

[zullo]

stopper means you don't have to make the holes in the plate should not be laundered if no, and useless to the air mass meter to a minimum, let's say 250 300 we might as well stay but must arrive a minimum of 600 on
the problem with the mass air flow sensor it can bring as well the egr spouting and is not properly closed

do na test stage, without egr hole and disconnect the mass air flow sensor and see if it goes better not to give the line that gives you the error of trying to understand where the problem is .

I did a test by putting a sheet on the pipe that goes to the valve, but with 3 holes by 5mm the middle of not ? changed nothing, the only thing ? now as the error always p0400 but instead of being excessive ? little and in fact does not erase it.
However, the means should not be just the way it should go, even so, can you please tell me when should measure the mass of air to the max?
I know that the minimum amount of heat must be from 35 to 47, and here we are, but at the max only comes to about 250, it seems a little bit on the 3500 rpm is so low