Report BDM with GALLO V2 clone

[s3alex]

Hello all,
dusted this discussion because I am facing my first connection to the ecu with Galletto.
I have the FGtech v54. After reading your guide I see that you have connected to the db15 connector to the Cock to feed to the electronic control unit and not to an external power supply as I did. Then you put a e xxx more between the wing and the control unit.
I have to say that I still have not managed to make it work in any way.
However, these are the connections that I made. Where am I wrong?
image2.jpgimage1.jpgimage3.jpg

[maku1977]

dima and schedule....... money well spent!!!!

[giuseppe89]

Hi guys I was heading into my first reading in the bdm with galletto v54 and template with schedule-spring...is my first experience and definitely I am doing some bullshit...I present the problem:I was referring to the document that explains to me what pitches should I connect and I read that the 14 it should only be used for 12 and so far everything is ok,I find what are the pitches, and when I'm about to lower the jig I realize that my e xxx spring has only ten skewers!!!!The adapter is called Bosch,the ecu is a edc16 a croma 1.9 mjt 120cv and now I do not know if I have the wrong adapter, or do I have to connect on only ten pitches.someone enlighten me please!!!I would not have caught a single jig!thanks to all

[cinqueturbo]

Hi guys I was heading into my first reading in the bdm with galletto v54 and template with schedule-spring...is my first experience and definitely I am doing some bullshit...I present the problem:I was referring to the document that explains to me what pitches should I connect and I read that the 14 it should only be used for 12 and so far everything is ok,I find what are the pitches, and when I'm about to lower the jig I realize that my e xxx spring has only ten skewers!!!!The adapter is called Bosch,the ecu is a edc16 a croma 1.9 mjt 120cv and now I do not know if I have the wrong adapter, or do I have to connect on only ten pitches.someone enlighten me please!!!I would not have caught a single jig!thanks to all

Carefully review the documents that you have, because it is described in detail the position of the pin, and are 10 the ones used on the Bosch..

In the BDM you have to be certain of what you do the risk of burning an ECU, and the most high..

Cattura.JPG

[giuseppe89]

Thanks cinqueturbo but on the pdf attached to the cock speaks of the 12 pitches,and then by dint of search I found on the forum the same solution,use the ten pitches, starting from the right, leaving so 4 free on the left side...the reading was good and I got 3 files totali.Su this ecu, I went there without many problems because it is a forklift, and then to give zero.I would now like to proceed with the reading of the edc16c39 for my delta 1.6 mj I have to apply in the same way? I repeat that in the documents of the cock there is nothing about them spoke of the 12 pitches, and on the ecu I can not do any damage!!

[cinqueturbo]

Thanks cinqueturbo but on the pdf attached to the cock speaks of the 12 pitches,and then by dint of search I found on the forum the same solution,use the ten pitches, starting from the right, leaving so 4 free on the left side...the reading was good and I got 3 files totali.Su this ecu, I went there without many problems because it is a forklift, and then to give zero.I would now like to proceed with the reading of the edc16c39 for my delta 1.6 mj I have to apply in the same way? I repeat that in the documents of the cock there is nothing about them spoke of the 12 pitches, and on the ecu I can not do any damage!!

It seems strange to me that in your manual there is the explanation or methodology to operate on the Bosch..

to also attached an image of the Pin

if you need the manual I can attach it

[giuseppe89]

Hello cinqueturbo the picture you attached is the same that I have I,but I placed the skewer in the spring, all on the right leaving 4 empty plots left and it worked,I extracted the 3 files ( all, eeprom, flash) now I would like to know if I acted correctly or should I follow some indication that I can't find the manual,I would like to read my edc16c39 but I'm afraid to damage.tonight from the PC I am attaching the photo of the connection I have made. Hello thanks

[giuseppe89]

pitches edc16.jpg this is the connection that I made.

[cinqueturbo]

pitches edc16.jpg this is the connection that I made.

I don't know what to tell you.. of course it's strange because those are not used by you there are 3.3 v and VF1 that I do not know miss what it is...

your edc16c39 flaw in the same way, not daring to put it otherwise because it'd send the 12v where you should not and zaffummm

[giuseppe89]

That is precisely what I would like to avoid...nobody knows something more?