info galletto v54

[Errecinque]

parts from that side to them, but it balances, or you have the e xxx.

this ? the pattern of pitches BDM give me with the V54.
Port BDM ECU BOSCH.jpg

and this ? the pinout of the galletto v54 (if someone can? tell me what is the meaning of the various terms is a favor to me and I think many others)
For example, the 2 gnd in parallel on the bdm port of the ecu where are they?
Pin-Out Cock V54.jpg

Then the e xxx adapter bosch port pinout 12 a 10-for-pin compatible with the interface galletto. ok now ? clear. In conclusion, putting the ecu on the template and I must get there (and then comb wiring to me) must? match the needle to spring starting from the first to the right of the pitches BDM. And the red strip of the flat must be on the right her as well right? Theoretically, to be sure you must first feed the check with a multimeter the various continuity? of links, for example, DSDO on port bdm will have? fit the pin 10 of the cock and cos? via right? Sorry for all these questions but in addition to do it for a friend for free I would not ricomprargli a new ecu

[blackwolf76]

To connect with the cock in the bdm with the template and the related schedule spring (for bosch has a 10-pin) you have to connect the starting to the right of the first image that you have put in this last post, considering that you have to put in the intermezzo of a special adapter with power supply provided with the cock, and the e xxx with needles towards the outside, and the connector and the inside of the template.

[Errecinque]

To connect with the cock in the bdm with the template and the related schedule spring (for bosch has a 10-pin) you have to connect the starting to the right of the first image that you have put in this last post, considering that you have to put in the intermezzo of a special adapter with power supply provided with the cock, and the e xxx with needles towards the outside, and the connector and the inside of the template.

But sorry if I e xxx spring 10 pin then 2 jump seats in correspondence with the 2 free pitches right? The template I should still get it and if, as I think the needles are still to be paid as I think I need to make sure that they correspond only to the pitches shown in the picture?

[blackwolf76]

you remain disconnected from the pin to the left frontae you. the e xxx you get 10 points and the control unit has a total of 14 pitches.

[Errecinque]

you remain disconnected from the pin to the left frontae you. the e xxx you get 10 points and the control unit has a total of 14 pitches.

But just to not do stupid things why? in the instructions of the cock they see that solder pin strip on 12 pitches, and attach an adapter bosch but with side entrance bdm 12-pin, which becomes 10 output towards the cock differs from that given in the endowment which has 10 from both sides ?

[blackwolf76]

You'd have to ask the people who produce it... The procedure ? that.

[Errecinque]

After a lot of thinking and with the c..or close ? gone!!! Read to the end, the flash 2048 jb eeprom 8 kb. Now let's write!!!!

At the beginning of the write to the message chk calculated in writing you want to fix it, I said no. I did right?

[blackwolf76]

If you have changed the file with a soft that calculates automatically, type the titanium does not need it to calculate the rooster, otherwise it is best to do this. I do always calculate.

[Errecinque]

If you have changed the file with a soft that calculates automatically, type the titanium does not need it to calculate the rooster, otherwise it is best to do this. I do always calculate.

Then my goal was to defappare and I tried with the flash file read with galletto. Then I wrote directly always in bdm the first time, saying he did not correct the chk and writing ? come to a good end. Come to doubt the I have rewritten telling him to fix the chk and gave me "error in micro" . I open titanium took the file processed with the time calculation chk saved file mod and rewritten in the bdm without telling cock-of-the correct and completed re-writing. B? between a few hours to see if the car part. PS : at the end of the write to the message "to turn off 10 sec then turn on the ignition and wait for 10 sec before continuing, " which one ? the exact procedure since giving ok you ref? wait a few sec and then tells you again "turn on the ignition? " (that was already? on " thanks

[blackwolf76]

time does not calculate cks, you can make the cock that anyway the fabsolo if you write the flash and not the complete file. after each write, it is better to wait 10 seconds to allow time for the flash to store the new data, from here, the switching on and off ome by the procedure of the program