I can not read the edc15p

[kingsnake]

you can try the pin out by removing the ecu, in the documents folder of the cock is the photo

This I might try to see if the problem ? the programmer

[angelolsp]

I am x now I have not had any problems myself for? I had heard that was not going well

[kingsnake]

The best part ? in the serial makes me do everything, edc 16c35 edc 17 Cp etc... But a trivial edc 15 no

[sisco]

I also had problems with 2 edc 15, respectively, of an audi a3, and a4 I have the rooster clone vers. 48 and I had already? changed to a resistance that the original was 10 khom with a 3.9 khom, then I changed again 2 resistors behind the rel? yellow and it worked, the a4, I've also written for? I don't know if it also applies to your version, search for qu? to know the value of the resistors http://www.professionalchiptuning.ne...1&d=1391261510

[kingsnake]

I also had problems with 2 edc 15, respectively, of an audi a3, and a4 I have the rooster clone vers. 48 and I had already? changed to a resistance that the original was 10 khom with a 3.9 khom, then I changed again 2 resistors behind the rel? yellow and it worked, the a4, I've also written for? I don't know if it also applies to your version, search for qu? to know the value of the resistors http://www.professionalchiptuning.ne...1&d=1391261510

Thanks for the info, after I have a look at the link you sent me.

I also had problems with 2 edc 15, respectively, of an audi a3, and a4 I have the rooster clone vers. 48 and I had already? changed to a resistance that the original was 10 khom with a 3.9 khom, then I changed again 2 resistors behind the rel? yellow and it worked, the a4, I've also written for? I don't know if it also applies to your version, search for qu? to know the value of the resistors http://www.professionalchiptuning.ne...1&d=1391261510

I clicked on the link but I do not see the page says I do not have the rights, bha... Could you tell me what are the resistors to be replaced? A strange curiosity?, you have the v48, my me ? was sold as v51, when I open the software it appears to me 084, ? a 48 or 51?

However, today I ordered the v53, the first I sent back because? he did not read well in kline, then I knew that I could just replace the resistors, now I should get a new model is free from this defect.

[sisco]

I clicked on the link but I do not see the page says I do not have the rights, bha... Could you tell me what are the resistors to be replaced? A strange curiosity?, you have the v48, my me ? was sold as v51, when I open the software it appears to me 084, ? a 48 or 51?

hello the resistors are the four masses behind the rel? yellow, starting from the 15-pin connector
n?1 470 hom
n?2 1500 hom
n?3 270 hom
n?4 1000 hom
084 or 048 or 51 perhaps they are all the same I think we write what they want, however if you have ordered the 53 you should not have more? need to change the resistors, at least I hope-why? what I don't have it

[kingsnake]

The values that I have indicated are those that currently mounts the programmer or the value of the resistors that will have to? substitute for?king?
Anyway thanks in advance for all the information

[Macchinista]

Find everything you need here: http://www.professionalchiptuning.ne...2-ver-52-3-led However, the ones that you listed sisco are the value of the resistors that you have to put. Seen my lived experience to check with a multimeter the resistance behind the rel? yellow even without disconnect. If you have already? the correct value does not need to be replaced. solitemante resolves only changing that to 10 khom with a 3.9 khom that ? mass to the left of the rel? the yellow a bit more? at the top.

[kingsnake]

For the moment, thank you, I'm now going to remove the wing nut and will see?

hello the resistors are the four masses behind the rel? yellow, starting from the 15-pin connector
n?1 470 hom
n?2 1500 hom
n?3 270 hom
n?4 1000 hom
084 or 048 or 51 perhaps they are all the same I think we write what they want, however if you have ordered the 53 you should not have more? need to change the resistors, at least I hope-why? what I don't have it

I have checked the resistors you mentioned, the ones I ride are all correct, in the meantime, just to I want to change the crystal with a quality? best

I have a p? of difficulty? acknowledge the components why? my Cock has the components with the initials abraded, for? in addition to the problem of the tdi edc15 I had no mange in particular, quandolo taken directly "from the other side of the world" me ? was sold as quality? A.

[Macchinista]

Also mine was a quality yet the K line was not working. The only resistance was different that detached from the other by 10 khom... If this on your own ? correct lascierei all com'?!!