have you tried to rifarlgli the fix (rewrite the eep) you never know which functions
have you tried to rifarlgli the fix (rewrite the eep) you never know which functions
You already tried this but nothing to do!!! I doubt that something happened to the voltage regulators (MC34036). I have replaced the capacitors as shown in the picture of the mod, but not the two integrated that you seem to be regulators (MC34036). Now, by measuring the voltage, for example, on the heads of the integrated HEF40106BT (vdd pin and vss pin), appears to be 8,99 Volts. And right then, this voltage is, or should be 12Volt??
Matthew
I am sorry not to be able to help more? from what you say, you're much more? ahead of me in these things I have only changed 3 resistors and with a lot of effort you will have to wait for someone more experienced to decide to give you a hand
hello machinist....maybe I should give you the directions you need to replace the chips with mc 34063 but on the capacitors leaves the basic ones, i.e. in the order of 220 mF 35v or with the same capacity but the voltage more than 65 es (instead of 470)
it also changes the capacitor 330 mf with a 100 mf 50v volt or higher es 63... also changes the last 100mf with a 10mfp 50v or 63v
as I have already stated in the forum view previous messages when you do a mod thrust as that of mbena you run the risk of stressing the regulators mc34063 with power too high....in addition, then, to make it stable, you should
buy filters tdk and the filter epcos that are very expensive and generate incompatibility with some units
listen to the advice make the modifications that I have said and will work.....you will probably have to replace the hef40106bt and perhaps the quartz if you are burned!!!!
just do it and let me know
Ok thank you very much. Them I try and change them. You held? updated.
Matthew
hi matthew , just give me a confirmation of the chips on your mobo are signed 34063 PMUTE?? if you need it, and with the permission dell administrator I can send you by mail the components signed MC 34063 I have a bag full
if I repeat administrator I may send me your address in a pm to my private mail so no one can violate our privacy, and you'll send them to you gladly if you want to the maximum is really a cup of coffee by way of recovery of costs....
I repeat once again the administrator to give me the permission? thanks.....
matthew let me know.....hello
The other questions. there are various types of converters dc called mc 34063. okay any one 8-pin?
Matthew
Thank you. if you could do it I would be grateful. however, the integrated mounts are now called: MC 34063 TY1211 the mobo ? green with rel? yellow tianling!Originally Written by davidepar
Matthew
hello matthew, I can confirm that if you have the relay yellow, and the symbol and mc 34063 are of good quality, perhaps best of my and I can confirm that in addition to the two resistors, the quartz and the hef4016bt I have only replaced two capacitors with the same capacity but voltage greater
63 volts instead of 50 cost less, are more stable and easy to find I'll give you the initials
100mf temp 105+ c 63v (replaces the mod 330 mf)
10mfp temp 105+ c 63v (replaces the fashion indicated with 100 mf)
I repeat, the only way, and stable, and the quartz oscillates properly ....if you make the change complete, the filter tdk and epcos costs a lot, and limit the bandwidth
but reading the technical characteristics of the mc34063 and specified that if the values are too high(see the capacity of the capacitors taken looking at the mobo from the left to the right
the original 220 mf ----------> mod 470 mf
the original 100mf------------> mod 330 mf
the original 10mfp-------------> mod 100 mf
the capacity is too large is handled poorly from the quartz and from the integrated hef....*****and a out of scale, I made some tests with the mod boost with this that I point you now
and I guarantee you that the cock and reliable and even faster with my mod ...
test on the ford focus 18 tdci year 2002 delphi
before the mod read only the id but it gave strange characters
after the mod only resistors without changing capacitors and replacing it with quartz+ integrated hef read in 13 minutes ......written in 27 minutes
after the same exchange capacitors but only two with power from 50v to 63v read in 9 minutes, and written in 18
this is my experience.....it works well even in bdm
to publish a complete list as soon as possible
ps for integrated that you need look ok from the administrator if you want I'll send them to you
a greeting
Perfect. Prover? with your mod. The rest waiting for the components.
Matthew
Write permission
Quote