Solution hardware failure galletto v2 ver 52 3 led

[davidepar]

Hello all , I am writing to you because I wanted to share with you the result of the hardware change to the ' s motherboard del galletto v2 ver 52 three-led!!!!
thanks to give me directions from the forum I managed to make it perfectly compatible with all the cars in l,the interface indicated

unlike what is required by the change complete to check the layout advised ...that is

1) replacement no. 2 integrated MC34063
2) replacement 1 capacitor, the first in the upper left 470 microfarad 35 v
3) replacement 1 capacitor 35 v 330 microfarad
4) replacement 1 capacitor 100 microfarad 35 v
5) replacement 1 smd resistor 470 ohm 1 res smd 1,5 kohm 1 smd res 270 ohm 1 res 1 khom more than 1 res 3,9 k
6) replacement of the resonator, 3-pin, with quartz metal 16 mhz
7) replacement of the integrated 14-pin st hec 40106b with integrated 14-pin philips hef40106bt
8) filter epcos b827905513n
9) filter TDK ZIY-2P
10) RES smd 120 ohm

in reality, the components of the mobo was already compatible with many of the pieces in the list
perhaps the fact that I proceeded to step by step

I changed then the resistors smd all those in serievicino to the relay and one knows 3,9 k present near the mc34063 already present
after this first step still does not read the delphi....but, the value in volts of the battery and the past, 11,2 -(insufficient) to 12.7 fixed!!!!!

this stability has allowed me to have a read error when trying to read the map!!!!!
it was already a big result as the first seemed to read but then don't create the file gave error!!!
then I realized that the integrated hec40106b theun st microeletronics was not suitable to carry out in a proper way
the management of the poll up power supply (dialogue) due to the presence of a resonator is very economical to place
a quartz quality with mobile metal (degree of precision high)

result..!!!!!! stable, fast, reliable reads and writes correctly with autochksum


drive, try the chevrolet captiva 1.9 read and write to an average of 12 min

ford focus tdci 115 hp delphi in the year 2002 read and write to an average of 18 min

audi a4 1.9 tdi reading written 12 min

tricore bdm without antituning read and written in 2 minutes (whole)

I still want to try the other drive as the simos and other...,if I can I know or do I do
with the next step!!!

take me to opportunity to thank all the users of the forum and the admin that with a lot of patience we bear!!!! and we are allowed to share
our passions in this great site!!!!! thanks again!!!

[Macchinista]

Good, good days should I do also I the same change...

[carlo abarth]

you can make a paint with the part to be replaced ???and where possima take the components??thanks!!

Hello all , I am writing to you because I wanted to share with you the result of the hardware change to the ' s motherboard del galletto v2 ver 52 three-led!!!!
thanks to give me directions from the forum I managed to make it perfectly compatible with all the cars in l,the interface indicated

unlike what is required by the change complete to check the layout advised ...that is

1) replacement no. 2 integrated MC34063
2) replacement 1 capacitor, the first in the upper left 470 microfarad 35 v
3) replacement 1 capacitor 35 v 330 microfarad
4) replacement 1 capacitor 100 microfarad 35 v
5) replacement 1 smd resistor 470 ohm 1 res smd 1,5 kohm 1 smd res 270 ohm 1 res 1 khom more than 1 res 3,9 k
6) replacement of the resonator, 3-pin, with quartz metal 16 mhz
7) replacement of the integrated 14-pin st hec 40106b with integrated 14-pin philips hef40106bt
8) filter epcos b827905513n
9) filter TDK ZIY-2P
10) RES smd 120 ohm

in reality, the components of the mobo was already compatible with many of the pieces in the list
perhaps the fact that I proceeded to step by step

I changed then the resistors smd all those in serievicino to the relay and one knows 3,9 k present near the mc34063 already present
after this first step still does not read the delphi....but, the value in volts of the battery and the past, 11,2 -(insufficient) to 12.7 fixed!!!!!

this stability has allowed me to have a read error when trying to read the map!!!!!
it was already a big result as the first seemed to read but then don't create the file gave error!!!
then I realized that the integrated hec40106b theun st microeletronics was not suitable to carry out in a proper way
the management of the poll up power supply (dialogue) due to the presence of a resonator is very economical to place
a quartz quality with mobile metal (degree of precision high)

result..!!!!!! stable, fast, reliable reads and writes correctly with autochksum


drive, try the chevrolet captiva 1.9 read and write to an average of 12 min

ford focus tdci 115 hp delphi in the year 2002 read and write to an average of 18 min

audi a4 1.9 tdi reading written 12 min

tricore bdm without antituning read and written in 2 minutes (whole)

I still want to try the other drive as the simos and other...,if I can I know or do I do
with the next step!!!

take me to opportunity to thank all the users of the forum and the admin that with a lot of patience we bear!!!! and we are allowed to share
our passions in this great site!!!!! thanks again!!!

[sportknight]

probably would have solved it already? with the integrated resistor 3.9 k and the quartz

[legendaryslave]

thanks for sharing

[giary74]

you can make a paint with the part to be replaced ???and where possima take the components??thanks!!

hi Abarth, I have already? made a few months ago these changes, putting into practice the council of Mbena, and for now it seems that have had a positive outcome.
I changed only some of the components; I have bought someone in the pi?, if you need it, give me a whistle.
Sar? happy to help (within the limits of the possible)

I can give you the chip, the resistance from 3.9 and the quartz

[motorsport]

Thanks for sharing,I would like to know if possible where to buy these components...

[motorsport]

probably would have solved it already? with the integrated resistor 3.9 k and the quartz

sportknight you can do a screen along with the integrated and resistance with quartz to replace?? Thanks

[motorsport]

so guys my not to this error as quoted by davidepar,I just try to improve it if c'? need why? until now, or did jtag, k-line can bdm,only a little problem yesterday on a c3 hdi sid 802 siemens are not able to get into boot mode, or had to unsolder the flasks AM29F400BB,I do not know if the problem is ecu or galluccio should I try it on another ecu to confirm the value in volts in the sw indicates 12.7 fixed,now I would like to know if c'? some component to be replaced or not!!thanks a lot

[giary74]

These are the changes which he sportknight

the cock modifiche.jpg