Delphi DCM3.7AP and Galletto 2 V53

[sportknight]

I'll give you a tip, the workshops and the Mercedes throw the delphi 2.6(I think) why? you lack, try to see if you have a

You do not in jtag

[corrado]

I'll give you a tip, the workshops and the Mercedes throw the delphi 2.6(I think) why? you lack, try to see if you have a

You do not in jtag

Thanks a lot , prover? to see , even if here in rome, the mercedes for the pins used a caliper I have asked for a figure disproportionate priprio because these pins sell them new only in a kit with all the pliers....
to the limit in the bdm you are aware of any other units that are easy to find , I could ask my mechanic if I fix one , even if not ? delphi.....just that I feel as I were advising you the BDM port

whereas, in the file I hope that the assistance will make me? directions to the pi? soon on what to do....
I aprofitto of your kindness to ask you if you still have available those files EPT and bin

Thanks a lot !

[msport (exil77grande)]

Thanks a lot , prover? to see , even if here in rome, the mercedes for the pins used a caliper I have asked for a figure disproportionate priprio because these pins sell them new only in a kit with all the pliers....
to the limit in the bdm you are aware of any other units that are easy to find , I could ask my mechanic if I fix one , even if not ? delphi.....just that I feel as I were advising you the BDM port

whereas, in the file I hope that the assistance will make me? directions to the pi? soon on what to do....
I aprofitto of your kindness to ask you if you still have available those files EPT and bin

Thanks a lot !

hello conrad, I'm sorry but between the workshop and the many people online I you'll be missed,I think I have understood that I look forward to our news,since I don't remember having to respond you may get in contact with us with your request?
I thank you in advance.

[corrado]

hello conrad, I'm sorry but between the workshop and the many people online I you'll be missed,I think I have understood that I look forward to our news,since I don't remember having to respond you may get in contact with us with your request?
I thank you in advance.

Good day to all ....
Hello Exil77grande , I was referring to the interface ... I know that I have explained myself badly . Thanks !

of course,arrives

Thanks a lot SportKnight ! when ragiungo 80 drain and let you know

returning to the test in bdm with another ecu , can you recommend another ecu, easy-to-twenty-four? and low-cost ? .... without "slice of ham"

excuse the many requests but if you happen to have two minutes to answer me , I would be very grateful .

Good day , and thanks again !

[sportknight]

of course,arrives

[sportknight]

I think he's talking about the assistance of the interface

[sportknight]

edc16 and marelli 6f3 should be pi? easy to find,for example, if you find an old 1.3 mjtd of a point from a demoman goes well

[corrado]

edc16 and marelli 6f3 should be pi? easy to find,for example, if you find an old 1.3 mjtd of a point from a demoman goes well

hello Sportknight ,
today I was a demoman and told me to give me a ride and see if that was ... to the fact ? the point was not there , while machines I have found many but I didn't know to recognize a edc16 , above the ecu is not c was written edc16 , how do I know if one of those can? be good ?

Thanks !

[sportknight]

usually are cos? the edc16

EDC_16.JPG

and cos? the edc15

ECU-Bosch-EDC15-CDI-0-281-010-598.jpg

[corrado]

[QUOTE=sportknight;66553]usually are cos? the edc16

EDC_16.JPG

and cos? the edc15

ECU-Bosch-EDC15-CDI-0-281-010-598.jpg
the edc 15 I see the image while the edc16 no ....
in the image of the edc 15 c'? just written , but in all the ones I have seen I do not wax wrote one and the other