exclusion egr on the eoc cp33

[guidotacco]

you have solved,what ? the right solution?

I just found these I am attaching the same to the file, maybe I was wrong a few bits however, I can confirm that diagnosis still working figure

[pdtechnology]

hi guys I scusao if I can not respond in a timely manner, but I have problems with the line anyway, I have not yet had the opportunity to test other solutions advise I hope to resolve the ppiu soon so place all hello hello

[spiki_x]

Hi,

I join my discussion. Pity that it was, because it would be appropriate to come to the conclusion of how tapare I'm EGR on these ecus evil. I have already made a couple of Opel vivaro, but I have only raised a little table of the egr, diminuento the quantity, just that you do not turn on the error light.

The project most current and a Lagoon of a friend of mine, who has made a bad purchase. Although not Fappata has consumption beastly (always above 8l/100km). I'd really like to help him before this machine will eat him alive. For experiment, we disconnected the egr from the intake and the fuel consumption is lowered, but breaks with the malfunction indicator light anti-pollution.

I extend my gratitude to you for any help!

MPC 561/562
FLASH S29CD016GB
EDC16CP33
EDC16CP33/01
EEPROM 4Kb

Bosch
EDC16.A0
1037390538
1037399650
------------------------------
Size: 2097152 = 0x200000
Cks = 0x1017E4ED

[pdtechnology]

hi guys the car to me ? returned to anke for only 5 min ? I have tested the board suggested by mat82 but does not act..is valve is working I need to try another solution as soon as I return the machine for the coupon that I have more time..will update good work

[spiki_x]

Do you think it would be validfo this trick:

Disconnect the starter motor of the EGR and erase the error that comes from the flash.
I tried to disconnect and the drive works normally , but comes out of the light engine failure. Deleting it should go.

[munro]

if disconetti the egr and clear the error how to turn on the framework will returns the error...
if there is no feedback signal to the ecu does not detect the egr do you give? always the dtc with relative indicator light mil on....
also when you close a file, the egr, however, must be connected and in most cases, working 100%.....
for? you could try to do as you say and switcciare the dtc related to egr in the map....
for? ? just a guess my....

[spiki_x]

Embracing this meant. Delete the DTC from the map.

But I suspect that then would jump out of a new error type: Flow EGR wrong..... and bisognierebbe to eliminate that too. If I can't find a classical solution we'll try and lighthouse to know

[msport (exil77grande)]

Embracing this meant. Delete the DTC from the map.

But I suspect that then would jump out of a new error type: Flow EGR wrong..... and bisognierebbe to eliminate that too. If I can't find a classical solution we'll try and lighthouse to know

if you unplug the egr and turns on only the light and the machine goes well you can disable the relevant dtc and you are affixed.

[munro]

bh? at that point, do as you f? for the de-fap...
the cio? clear from the map all the dtc related to egr.....
so not scassa the testicolame......

[spiki_x]

I have two patients in the clinic. A lagoon and a qashqai. The lagoon the written sriale with the cock. I restored the injectors and the VIN, But the cruize control does not work!!!!!!!!

I have tried with the CanClip.... but nothing, it won't let me even to enter. Even with autocom gives me error of Wrong ID.... you will be missed that too. Now I try to re-open the ecu and reset the eeprom that I've saved in the bdm. Now I am afraid to make the qashqai in serial in order to avoid similar problems..... Someone has experience with similar situations?