scania 164 480 bosch edc ms 6.2 how to read this ecu?

[sisco]

hi joseph my cock ? the one with 3 leds, the version says to me, 0084, I do not f? ecu data, with regard to the k-line that I did on the pins of the ecu I'm sure that works, because to test it I entered with scania tester that precisely communicates in k-line (on this ecu), it remains only for me to think that maybe the rooster is faulty in reading on the k-line, if you see the post n? 10 see the connections that I made, (what ? a schema scania) I looked at the pinout you posted and feeds the masses and k-line are as in my scheme

[frantik3]

Bosch Ms6.2 if not the law try to unsolder and do it before

[klajdin]

.. I also have the version with 3 led's but the first in the series, the one with Hw 0048, these are a p? screen as I said before, for? I do not have more? one of the daily Ms6.3 ( 12V ) socket 38-pin, instead of the adapter 30-pin that I had taken had hurt so I used 3 wires to connect to the diagnostic socket, but it worked after the fix of the resistors and integrated !

[giuseppe1374]

hi joseph my cock ? the one with 3 leds, the version says to me, 0084, I do not f? ecu data, with regard to the k-line that I did on the pins of the ecu I'm sure that works, because to test it I entered with scania tester that precisely communicates in k-line (on this ecu), it remains only for me to think that maybe the rooster is faulty in reading on the k-line, if you see the post n? 10 see the connections that I made, (what ? a schema scania) I looked at the pinout you posted and feeds the masses and k-line are as in my scheme

you have the same cock is mine and you can go quietly to read from the odb put the cable boot to be clear what you use it for the boot tricore and you connect with the pin to the socket odb, from what I understand the tour you are not able to do because? you would be missing some power

[giuseppe1374]

sorry for the double post, open the cock and see if you did the fix for the kline

[sisco]

hello joseph, I think I have put all of the feeds, maybe it's not the law in the k-line, during the week I do a few test on some car that I am sure that both k-line and see if it reads or not and if not the law, I open it and check the components as explained in other posts of the forum; I checked the cable for the boot tricore and to pin 7 of the wiring of the boot there are 2 green wires that the manual boot tricore called "ingniction" , virtually are connected where ? cable is connected to k-line, and therefore should not change anything from the link that I have done ,or am I wrong?, another question ,have you connected to the 24 volt?

[sisco]

thanks klajdin for the screen I saw that you read the stralis I turned on my cock and I saw that the driver for the stralis says k-line villa is definitely my cock avr? some of the problem, as soon as I make sure of all of this before I read well what ? been written about it and if I can't get alone I ask for a help , I salute you

[klajdin]

thanks klajdin for the screen I saw that you read the stralis I turned on my cock and I saw that the driver for the stralis says k-line villa is definitely my cock avr? some of the problem, as soon as I make sure of all of this before I read well what ? been written about it and if I can't get alone I ask for a help , I salute you

..no problem, from what I can gladly help !!

[giuseppe1374]

then, the green wire is called the ignition for the edc17 for the other ? kline then you need to use for the kline, I've used the 24v on a stralis and it has worked, I have to ask you a question, since you've used two different feeds a 12v for the chicken and a 24v for the ecu you put the mass in common?? then if in case your rooster does not have the fix you have to change 2 resistors nothing in particular.

[sisco]

then, the green wire is called the ignition for the edc17 for the other ? kline then you need to use for the kline, I've used the 24v on a stralis and it has worked, I have to ask you a question, since you've used two different feeds a 12v for the chicken and a 24v for the ecu you put the mass in common?? then if in case your rooster does not have the fix you have to change 2 resistors nothing in particular.

no joseph the mass in the town I put for? I have read a via can with this system food, the cock 12 and the ecu 24 and it worked