Map alfa 159 120 hp

[antonio.o]

Port to 0, these addresses: 1C4B6E to 1C4B84 then 1C4C3A to 1C4C50 cos? you'll egr closed electronically, then after this operation, you can also close physically with a flange.
To bring it back to the ori selections the two addresses and click on the button in the top right that has an exclamation point in a red semicircle.
If the map ? still, my advice ? to lower the turbo 60-70 points and put ori the map in the ecm (I speak of the titanium) calls "a Percentage of valve opening".
For tips + specific you have to wait for some good samaritan pi? expert

Hi sorry but can you help me understand how to move with the ECM to find and change these values.
Thanks.

[antonio.o]

Hi sorry but can you help me understand how to move with the ECM to find and change these values.
Thanks.

Maybe I should not ask but I would like to understand something hello.

[panterargento]

Maybe I should not ask but I would like to understand something hello.

Then load your map ori in the ecm, load the driver, then open in 2d mode? motorola 16bit, right below where you wrote "go to" add this address 1C4B6E by sending, restrict the horizontal zoom to 160, then the vertical moving one step to the right, remove the check mark here +/- if c'?, select the two contolli from 1C4B6E to 1C4B84 then 1C4C3A to 1C4C50, then take a look at there st? a "m" tiny st? to indicate the minimum value, click on it, and you'll have closed the egr.
However, I am attaching the map with egr off, cos? when you reach to the useful messages, you will have a better understanding.

[antonio.o]

Then load your map ori in the ecm, load the driver, then open in 2d mode? motorola 16bit, right below where you wrote "go to" add this address 1C4B6E by sending, restrict the horizontal zoom to 160, then the vertical moving one step to the right, remove the check mark here +/- if c'?, select the two contolli from 1C4B6E to 1C4B84 then 1C4C3A to 1C4C50, then take a look at there st? a "m" tiny st? to indicate the minimum value, click on it, and you'll have closed the egr.
However, I am attaching the map with egr off, cos? when you reach to the useful messages, you will have a better understanding.

ok, thanks for? for a non-expert like me ? hard to get to 80 ms.

[panterargento]

I learned qu?, and I'm not an expert...far from it.
You'll see that there arrivals...

[antonio.o]

ok, thanks for? for a non-expert like me ? hard to get to 80 ms.

we are able to close the egr thanks to your help.

[antonio.o]

hello people m id? a hand to remove the fap control on this machine.

[panterargento]

hello people m id? a hand to remove the fap control on this machine.

Here is your file with egr off and dpf off... don't ask me how I did it why? I used ecusafe2 to remove the management...scorrilo in 2d and see the differences...it works for me because I have your same car, but the 150 hp.

[antonio.o]

Here is your file with egr off and dpf off... don't ask me how I did it why? I used ecusafe2 to remove the management...scorrilo in 2d and see the differences...it works for me because I have your same car, but the 150 hp.

thanks you have been ultra polite for? unfortunately I do not have the permission to download it, maybe in pm nothing?.

[panterargento]

thanks you have been ultra polite for? unfortunately I do not have the permission to download it, maybe in pm nothing?.

I do not think the regulatory...try to send a pm to msport and see what it tells you, if I authorize it, then not c'? problem, otherwise you'll have to wait for the helpful messages...