opinion on mapping panda 1.3 mjet 70cv

[marco]

sorry dvdtuning I would tell you but none is a rebuke also because I am a beginner that 2d does not tell you that if map1 is needed for a particular function so according to me, put it in the confusion? however, are to serve for the entry diesel oil in the engine.

[Ducati87]

but you have not written that you didn't want the soup ready?

listen I don't want the meal ready for it? if I miss a information you can? then I really think that my topic here is totally useless. I'm not a magician and I want to do an experiment that can affect to my car, I'm here to ask for advice and to learn, but if I don't you can? 't even tell the difference between those three maps so I don't understand anything of this forum. thank you and I go on.

[Gianpy80]

ducati87 I assure you that is not ? cos?.. In this forum c'? a lot of people willing to help.. the staff for the first.. if you want a board catching fleas in the forum, is looking for a p? discussions that interest you and start to learn the basics.. when you get to 50 posts you can download the guide and begin to do the tests..
Then the seats following the correct procedure and you'll see that you will answer correctly.. What I've learned ? that to get the right answer you need to make the right question

[Ducati87]

ducati87 I assure you that is not ? cos?.. In this forum c'? a lot of people willing to help.. the staff for the first.. if you want a board catching fleas in the forum, is looking for a p? discussions that interest you and start to learn the basics.. when you get to 50 posts you can download the guide and begin to do the tests..
Then the seats following the correct procedure and you'll see that you will answer correctly.. What I've learned ? that to get the right answer you need to make the right question

there prover? thanks for the straight

[msport (exil77grande)]

perhaps you don't understand,then you open a post with a question, and I specifically answered what you asked, and not a little,then you are asked if you eliminate the egr valve and I answered that here there is the jelly is ready, but all the help that you need but the work you do with our aid,tips and guides that you still can't see, and you said there is no problem because I proceeded to let me do another one at this point if you tell me that you don't want the jelly is ready, because cloth did you make another? and all of this, what about el questions that you've done that you have responded?

[magi1984]

listen I don't want the meal ready for it? if I miss a information you can? then I really think that my topic here is totally useless. I'm not a magician and I want to do an experiment that can affect to my car, I'm here to ask for advice and to learn, but if I don't you can? 't even tell the difference between those three maps so I don't understand anything of this forum. thank you and I go on.

ok then,to make you understand a p? your map and give you the full info in the ecm titanium drivers for your map you have:

injection time that the ecm calls injection zoned
maps accelerator pedal that ecm's called torque limiter
torque limiter ecm called the torque limiter #2
torque limiter ecm called the torque limiter #3

out of the driver you have to the following address:

646a4: advance injection
6922c: limiter fumes
6967a: rail pressure
6957a: rail pressure limiter
69ac2: rail pressure limiter
62bb0: torque limiter
6add4: torque limiter
6adfc: torque limiter
6ae44: torque limiter
6ae5a: torque limiter
6ae94: torque limiter

now you have everything there? you need to map your car.
as you can see on this forum people are helped really, just have patience

[cicciogsr]

6922c: limiter fumes ? in the marelli s me? that ? pi? a lim of diesel not reported to the air flow rate measured

[munro]

6922c, and a map of lambda for high Iq..at least that is called from winols....
in the axes X,Y, there are mg/stk MAf and RPM the descriptor ? the AFR and the conversion factor for this ? 0,001302
then
6957a ? the limiter rail as a function of boost turbo conversion factor for Z-axis=to 7.51...
69ac2 ? the limiter rail as a function of temp diesel
6AE94 ? the lim of torque as a function of temp diesel z-axis ? in NM, and the conversion factor ? 0,023438 comep er all other lim of the couple while in the Y-axis of this address, the temp should be converted to the factor 0,5...as well as all the other temp in the map...
in addition, there should also be a in lim torque as a function of temp engine 6BA3A if I'm not mistaken.....

[magi1984]

6922c: limiter fumes ? in the marelli s me? that ? pi? a lim of diesel not reported to the air flow rate measured

I call the map lambda limiter fumes

[cicciogsr]

I call the map lambda limiter fumes

ok have you figured out how to tap it? according to me you should honestly I never tried