Hello to all.
I have an alfa gt 150 hp mjtd edc16c8.
I have a small map that is loaded.
I installed 2 pressure gauges-pressure turbo that can give me both of 1.75 bar peak, then down to 1.65 bar.
I have tried many different sensors to read turbo pressure, including one that should read up to 307000 hpa.
But the diagnosis me always 1.52 bar maximum...why?
Thanks for the replies.
Easter
Mmmmm... have you tried to change the pressure sensor?Originally Written by easter
"The only thing that stands between you and your goal are the********* continue to tell you why you can not reach it."
Hello and thank you for having responded to me...I have changed 3 of the original bosch, more and 1.52 bar. Even with the 3bar absolute nails to 1.52 bar that is 2.5 bar absolute. The thing is 'nasty'!
But, and mapped or touched electronics is the machine?
maybe, and been touched a few BP that blocks the view with tool..
in addition it can also depend on the instrument reading, test with other diagnostic..
I have a family of EDC16C8 me happened to have the delay of reading but not posting, reading between the gauge and the sensor aggiornaci..
"The only thing that stands between you and your goal are the********* continue to tell you why you can not reach it."
The car is mapped, but was not touched no BP unknown. I used titanium and the only interventions outside drivers were the ones to close the egr, the panettoncino of 4bit to unlock the prex rail 1450bar and the bits to unlock IQ.
But tell me: The EDC16C8 that you have in the family exceeds 1.52 bar diagnostics? Can you try please?
But tell me: The EDC16C8 that you have in the family exceeds 1.52 bar diagnostics? Can you try please?
If it is a proof that you have already made you read at least 1.6 bar from diagnostics?
If yes, the code of your pressure sensor is 0 281 006 028 - 0 281 002 437 - 0 261 230 313 - 0 281 006 076
I will try to do a reading with MES...as soon as I can...because it's pulling the 5th gear and I have to go on a track so close!
Here is my map...do you like him?
You I jobs facts and turns to 1,8 pressure is the gauge of the diagnostic..
then you used the other right now?? test and updateIf it is a proof that you have already made you read at least 1.6 bar from diagnostics?
If yes, the code of your pressure sensor is 0 281 006 028 - 0 281 002 437 - 0 261 230 313 - 0 281 006 076
here you take me unprepared..I can see and let you know..
I will try to do a reading with MES...as soon as I can...because it's pulling the 5th gear and I have to go on a track so close!
"The only thing that stands between you and your goal are the********* continue to tell you why you can not reach it."
Easter but have you seen improvements with these maps?Here is my map...do you like him?
turbo you require maximum 2493mb so little 1.5 Bar you haven't touched vgt and with the little bit of diesel that you've added and you have unlocked, I doubt it exceeds the 1.6..
"The only thing that stands between you and your goal are the********* continue to tell you why you can not reach it."
This is the map that I currently have on.
The test bench says 200cv.
Do you know this map at this address?: 0EBEDE
The map I posted at the beginning is the one that will get if you fail to solve the problem of block to 1.52 bar. This is because despite having the limiters 1.65 bar when you nail it to 1.52, and spend 10 seconds fails with error p0235.
anyway....
If your edc16c8 in diagnosis makes 1.8 bar then the sensors I have tried are all high...then I ask you, please, tell me the code of your.
But the odd jobs they did you? I ask because we are sure that there is a few bits, hidden, lock manager to 1.52 bar.
Thank you and good evening.
Quote
