a little smoke...a few performance

[sportraxxx]

in the 2d map to display in motorola 16bit..

Ok...I try this way

[sportraxxx]

then I'll tell you a little bit of maps for your ecu then if you have difficulties on how to
to change them tell me that I'll tell you how to act..
below I'll give you all the maps that are not in the titanium ones that you said
the sw if you don't know what they do and how they work you can ask..
so for a start you have
address
0c0320 (7x1) a map that reduces torque to impostaala all to 0
0c0864 (7x7)map of the correction torque in the f-speed engine and vehicle
set it all to 8192(I did not ever changed and
try to see how it behaves in the car) you can
try also to reset it all
0c0be2 (14X1) this is a limiter of iq as a function of the aspirated air via maf
set how much you want to inject
0c0c74 (4x1) limiter iq set it to how much you want to inject now is to 60mm3
0c0c7a (5x1) limiter iq for low rpm set ahow do you want to inject
0c3910 (1x1) single-bit limitation of air mass to 1500mg
0c391e (1x1) rpm limiter to 6000 rpm if you want to shoot then down for a 5350-5450
0c3928 (1x1), single-biti-limiting iq set at 100mm3 for now, do not touch it
0c5158 (16x16) map nm>iq in regeneration return it ori or, leave it so
0c5536 (10x1) limiter torque your axle spins and touched the evil as it is put in place
0c5562 (10x1) limiter torque
0c558c 10x1 limiter torque
0c55b6 10x1 limiter torque
0c55de 9x1 limiter torque
0ccffe 1x1 single bit limiting rpm for the pop corn, also this should be lowered
0cd454 20x1 torque limiter
0cd4a8 20x1 torque limiter
0cd7b0 8x8 limiter iq set it to straight line to 100mm3
0cdfbc 4x1 limiter iq set to 100mm3

for now just this and then I can just tell you the rest..

good evening,I started to experiment with the program in the ecm...something I do not is still not clear:
for example, where I've written
"0c0c74 (4x1) limiter iq set it to how much you want to inject now is to 60mm3"
how do you see that it is 60mm3?once you set the address we are interested in and highlighted the curve as it gets to go from the graph the values?

[munro]

what do you mean by chart values? go from 2d to tabular?if the map and off the driver can't display it in the grid, but in 2d you can change easily as the most you like...

[sportraxxx]

what do you mean by chart values? go from 2d to tabular?if the map and off the driver can't display it in the grid, but in 2d you can change easily as the most you like...

well I understand,so when you tell me that for example the injection is to 60mm3, I will if I have to wear it for 80 example, with the 2d, you calculate the percentage of surcharge and run, the increase of the curve...right?

[munro]

if you look at the 2d map 4x1 and set to 6000 in decimal is equivalent to 60mm3 to take it to 80mm3 you have to take it to 8000 decimal points

[sportraxxx]

if you look at the 2d map 4x1 and set to 6000 in decimal is equivalent to 60mm3 to take it to 80mm3 you have to take it to 8000 decimal points

well..slowly beginning to understand...

[munro]

well..slowly beginning to understand...

you have chosen to learn about a ecu quite complex...
eye...

[sportraxxx]

yes, I noticed..