golf plus 1.9tdi 105hp review, egr

[cawadany]

so guys we do not make confusion,the first example as already said it was fine the first control and the second was almost perfect, but it was not ok,in this last example, however, I saw that the first control is ok, and the second you put gold, but it remained a small mod on then forgive ori the second control then check the box to your right, next to 8bit where it says +/- at this point all of the maps you move to the destination screen, and the control becomes visible as the first, and select from 0D5346 to 0D535E exactly to these addresses at this point, just re-check the box that you previously selected +/- and all the maps you rispostano low as at the beginning,you can now select m tiny and the control is perfectly clear, in fact, if you re-select the check-box +/- see the control perfectly clear as the first,I hope I could explain in case the test and places, or if you have other questions to ask,good job.

However, I think you were wrong to indicate the addresses. By selecting the +/- the maps are brought to the centre, and if we want to reset the second one as the first one I need to bring to zero by 0D5344 to 0D5360. Or am I wrong?

egr off +-.jpg

[msport (exil77grande)]

However, I think you were wrong to indicate the addresses. By selecting the +/- the maps are brought to the centre, and if we want to reset the second one as the first one I need to bring to zero by 0D5344 to 0D5360. Or am I wrong?

egr off +-.jpg

I confirm what was previously written, for me the addresses you want to select are from 0D5346 to 0D535E because as you have selected you there are some maps where the controls are slightly different and would be unpacked,you will always select from the top never from the bottom point,guys without presumption I these controls do them with your eyes closed and think so if anyone has different ways and is right on the cg?he will do as he sees fit.

[cawadany]

I confirm what was previously written, for me the addresses you want to select are from 0D5346 to 0D535E because as you have selected you there are some maps where the controls are slightly different and would be unpacked,you will always select from the top never from the bottom point,guys without presumption I these controls do them with your eyes closed and think so if anyone has different ways and is right on the cg?he will do as he sees fit.

You are right, I am confused.....

[ago27]

thanks msport, finally I managed to do that then was not very difficult, I feel I have a cable vcds 10.6 and that you know the steps to see if the EGR and closed. Thanks

[msport (exil77grande)]

thanks msport, finally I managed to do that then was not very difficult, I feel I have a cable vcds 10.6 and that you know the steps to see if the EGR and closed. Thanks

we are here for,no I'm sorry for this I can not help you open a post in the suitable section of surely someone unfamiliar with this cable you can find it.

[ago27]

but just to know the first control as you adjust it ????? No because I have modified by hand, the cio? I selected the two addresses, and then less, until and down to -100,0, or there is a method more simple to do it as the second control, i.e. by pressing m.....thanks

[msport (exil77grande)]

but just to know the first control as you adjust it ????? No because I have modified by hand, the cio? I selected the two addresses, and then less, until and down to -100,0, or there is a method more simple to do it as the second control, i.e. by pressing m.....thanks

certain you need to do exactly the same thing i.e. to select the beginning and the end of the 2 top corners, and then select m lowercase of course, the map must be in the bass if you have +/- selected or not, and it's done.

[cawadany]

but just to know the first control as you adjust it ????? No because I have modified by hand, the cio? I selected the two addresses, and then less, until and down to -100,0, or there is a method more simple to do it as the second control, i.e. by pressing m.....thanks

Am I wrong or the first control does not ? perfectly to zero?

[admin]

There are two cakes to bring to zero. The first ? ok. The second you have not touched, and ? addresses 0D5340 - 0D536A

guys please let's not talk about panettone christmas is coming and I are making me want a beautiful panettone

[cawadany]

But the second panettone is not to be cleared in this way?