the map posted I can't check,but regardless plain rip offs here and there,on maps for another "different",is not the best, and this already has been explained
the map posted I can't check,but regardless plain rip offs here and there,on maps for another "different",is not the best, and this already has been explained
The last map I modified it myself,I have been inspired but not copied.if I could check the map posted you would have known.if you can not answer just to do something,without giving any tip or shoot phrases.Try to be constructive.thanks
I don't see why you should be angry with so frenk85, not being able to see the files you said what you understood from my response, very likely, in any case, your edit is so not okay, you have changed only limiter, and foot pedal and evil, not just to hear the differences, it is useless to look at other files and make similar changes without knowing what you are doing.
p.s. I don't know if it's a constructive response, but I don't know what else to tell you.
ugo ---- president A.E.P.
Good morning,sorry for the tone, are not pointed out, I was hoping to see suggestions...the changes in reality have made by taking information from the internet. I scopuazzato only the first that I put at the beginning of the split to The other as I said I have changed thanks to the information taken on ******.cmq are all ears on what to change and whyOriginally Written by ugoboss
tips...............it does not seem that you have been given.....construction we are!! you?!? if you want a map there are no problems you do so you will plain rip offs instead if you want to learn to MAP,understand the increases,take out limiters, etc., is another thing
I have given the tip,the parts from the first map, that is the egr, and then scroll down to view all the other
then the egr, I've already changed, and in addition to that I modified the foot pedal, the torque limiter.
For costrutivo I mean that it is useless to tell me "you've changed only limiter, and foot pedal and evil" tell me where is wrong and why. So you do not learn anything..
I imagined myself that it was not a map is made well,but at least know why....
Anyway if anyone has a suggestion ,for those who do not know what a tip it to him, I remember me, is a hint when I say this is wrong for this reason,I would have done so.....this is a tip. Anyway there is no problem, I just don't think that this is the spirit of the forum; if you do not have information costrutive and useful to learn ,friends as before and I can even close the rear (I hope).
Thank you for your attention!
change pedal and the ldc does not bring power,briefly, a engine to develop the power he needs to rake in as much air and fuel as possible,so I advised you to from them.in the change the ldcs, everyone has his own methods,you can linearize the curve by putting a unique value in the tables (e.g. 500) from 1000 to 5200, or by opening the 2d and change it to a percentage,set the percentage,click on the map on the dim.desired,add and save.the pedal should instead edit the curves.parts from the third bend and starts to change so gradually increasing as you go ahead.if you want something more at the high speed you have to "rebuild" the last curve, let us case, there is no stops to 4500
hello frenk85,thanks for taking the time dedicatomi and the explanation...
then the ldc can't change it only in the table,if I open it first in tabular and then in 2d,I don't know if the fact that the map.I think the beginning where there is the first curve, but I don't know where it ends.
axes what I have? engine rpm and load?
it is really compicato.You can do a good job also in the table? in the event cmq I wanted to go back in 2d as I understand it is the curve that I'm looking for?
I then tried to search the 2d the pedal.....if I put them directly in 2d as I recognize the third curve?? if I go through the chart,the first part is a straight line up to an address where it begins a curve....but the map is only one curve?
you are wrong the display, you have to look at 16 bit, you have the 2d set to 8 bits, the pedal begins to 0794E2 and ends 079540.
ugo ---- president A.E.P.
after fixing the display,the ldc is:07886c-078890 the pedal, the said ugoboss you are affixed.
now open in 2d, "the injection phase"(egr) that you have already modified, and then scroll down,you have map mass air flow sensor that we leave it as it is, and get the injection split (map1) (boostxrpm) go to the address 072512 up to 072526 and draw a line(imaginary) dim 11 set the percentage e.g. 10% increments.this you do for all of the following curves,to confirm the changes, then return to the table click file,save as map increases.then open another map (map2)click file,load the map.click increases that you saved previously and confirm.with this you've changed the various maps of the time of the injection,not to be confused by the amount of diesel injected.
Quote
