Reading bdm marelli 6f3 or 6jf

[anniver]

Hello to all from the outset that these ecu, or made always in the obd a short time ago, I wanted to read a marelli 1.3 mjt 6jf or 6f3 in bdm I've got a template, and two of schedule marelli one large round and one small square


1 or unsoldered resistance
2 powered the pin out as it says fgt
3 set up the e xxx brush

that is:
e xxx/cmd(without pulling it as instructed)/galletto v54(clone)
I select mode bdm no jetag connect nnt says: micro is not supported
exchange e xxx the same.
exchange cmd (because in the end, or two, one with led and another without ) nnt always the same

something wrong or my cock nn can make the reading bdm
there would be a way to test the bdm of the cock?
if you want them tell me which one .

thank you in advance for your availability

[pippo65]

Hello to all from the outset that these ecu, or made always in the obd a short time ago, I wanted to read a marelli 1.3 mjt 6jf or 6f3 in bdm I've got a template, and two of schedule marelli one large round and one small square


1 or unsoldered resistance
2 powered the pin out as it says fgt
3 set up the e xxx brush

that is:
e xxx/cmd(without pulling it as instructed)/galletto v54(clone)
I select mode bdm no jetag connect nnt says: micro is not supported
exchange e xxx the same.
exchange cmd (because in the end, or two, one with led and another without ) nnt always the same

something wrong or my cock nn can make the reading bdm
there would be a way to test the bdm of the cock?
if you want them tell me which one .

thank you in advance for your availability

Hello,but is a 6f3 or a 6JF,because the first with the Cock, the real reading you're only in the BDM instead of the second if I'm not mistaken, you also in eobd.
You have selected BDM MPC 5XX?
Did you try to select 3v or 5v?
However, if you have done everything correctly, I have to say that the rooster which has no internal components that are quality,you say because there are the past.
Otherwise post some photos of the connections.

[Errecinque]

Usually when it says Micro not supported is because they are not made well, the needles on the pitches. It happens to me sometimes, and repositioning the e xxx, then it works correctly

[pippo65]

Usually when it says Micro not supported is because they are not made well, the needles on the pitches. It happens to me sometimes, and repositioning the e xxx, then it works correctly

I agree fully!!!

[pippo65]

The other thing to do is to clean well the pitches with proper detergent.

[giuseppe89]

Try and check for a well schedule,I've personally had problems with the connections between the plug and the needle of the e xxx not to mention the incorrect links found on a e xxx siemens between the various Pins and the various pins

[todos]

If you want to check for good you have to solder the wires on the pitch then the colleges on the bdm, so see if it actually works or not..........

[pippo65]

If you want to check for good you have to solder the wires on the pitch then the colleges on the bdm, so see if it actually works or not..........

I usually take rather than welding, I prefer to check with multimeter if there is continuity, the departure of the flat along the e xxx needle holder.

[blackwolf76]

put the adapter for the bosch without to feed it, you'll see that it works...

[anniver]

foo I know that the 6f3 in the obd are read only in the virtual

my question is, given that they are in possession of two schedule marelli one large round and one small square by observing the slopes are different but entambbi use only 5 pin so if anyone knows the numbering of port bdm and the pin of the output of the cdm can directly solder these 5 wires and check operation