Interface and software brera 2.0 jtdm 170 hp

[6bazz!]

Hello all,

I tried to make do with trying to understand independently and interface and software to use to read and write maps on the brera 2.0 jtdm 170 hp.
I read in the forum who has read the map with galletto v51 but in the list of the cars that are supported by the software I can't find mine.
In the network the only interface in the list of which appears in my car ? Kess v2 but the numbers are very high and I have not found the clones.
Being a beginner, I would like to buy them all without spending a lot of money and I was hoping you could advise me of you a clone valid.
I imagine that several of the forum is to be found in the face of these units that I guess they are the same for the brera and 159 2.0 jtdm 170 so I hope in your help.

If you ? gi? discussed this topic and I did not find in the forum, forgive me and reindirizzatemi you please.

Thanks

Sauro

[Alfa159 q4]

Hello, do you do with the rooster, serial or bdm, fits bosch edc16

[6bazz!]

Hello Alfa159 q4, in the meantime, thanks for the reply.
I knew that mount edc16c39 cos? as the 2.4, but I also know that this is not enough to be certain that it can be rewritten (should change the software, right?). You have had personal experience in this regard? Sorry if I seem suspicious, but ? just because you? starting from zero, and the cio? I have to buy everything I wanted to be sure.
Thanks again!

[ugoboss]

if you can reassure you say that you made the bdm with the version 48, read and written all ok.

[6bazz!]

Thanks ugoboss, and via serial? do you think there are still problems? To start I would say that to me ? better... Thanks again!

[voglioimparare]

should be mpps even if I'm not mistaken, as a software x to start the search in the network, titanium,or even better, map3d...all available in the network

[Backgroop]

Hello 6baz This ECU does not read with mpps in the bdm can do it but you just have to choose the protocol manually, if I'm not mistaken this is the 39.. CN the cock v53 the laws surely...

[ugoboss]

Hello 6baz This ECU does not read with mpps in the bdm can do it but you just have to choose the protocol manually, if I'm not mistaken this is the 39.. CN the cock v53 the laws surely...

exact if the laws with bdm100 you have to choose the family edc16+39 if you do it with the gallo2 that both version 48-84-51-53 - te the law in automatic, serial no I tried it for reasons of time, but I think that with the brera 2400 or 159 of the laws , and if the read and the write.

[6bazz!]

exact if the laws with bdm100 you have to choose the family edc16+39 if you do it with the gallo2 that both version 48-84-51-53 - te the law in automatic, serial no I tried it for reasons of time, but I think that with the brera 2400 or 159 of the laws , and if the read and the write.

Hello ugoboss told me to be sure that with mpps or galletto can you? tranquillamnete to read my ecu for? I stress, though edc16c39 has a software is different from that of the 2400. In the network, moreover, I saw in the lists of the various car supported by mpps that the cock that my car doesn't ? this. If, at the time of the reading of the ecu do not find listed my car as I do? there are alternatives?
Thanks as always for the support!

[ugoboss]

Hello ugoboss told me to be sure that with mpps or galletto can you? tranquillamnete to read my ecu for? I stress, though edc16c39 has a software is different from that of the 2400. In the network, moreover, I saw in the lists of the various car supported by mpps that the cock that my car doesn't ? this. If, at the time of the reading of the ecu do not find listed my car as I do? there are alternatives?
Thanks as always for the support!

you already said and I repeat do not trust the lists of interfaces, and a edc16+39 and read with interfaces that have this protocol, then if you take a gallo2 the laws in bdm and at that point you're good to go.