EDC16u1 Mappina

[Fedex]

Hi,
I am an amateur but I tried to make a map very soft on this unit ? mounted on my A3 140cv BKD no FAP.
The same power unit is mounted on the golf 5 series.
What do you think? Opinions,insults, suggestions and anything else that is useful....
PS: I hope I do not deserve "Map joke"

[Ghizmo]

EGR and hot start are ok, I guess I've made with some software.
The map ? practically non-existent, there are also errors in the editing of some of the maps.

[marco]

hello, I advise you to study a little bit on the forum before putting his hand to the map you will see that some things will be more clear!

[Fedex]

EGR and hot start are ok, I guess I've made with some software.
The map ? practically non-existent, there are also errors in the editing of some of the maps.

The Egr, I made it with Time, while the hot start, I did help...
However, perhaps while I was doing the map, I actually ? escaped under the control objective, namely, to make a map to reduce the consumption of trying to give more? torque at low rpm.
Errors in maps such as what kind of? instead, I noticed that where there are more? maps, ECM at the time of confirming, asking me to bring back the increases on similar maps and check there? known of the HORRORS, as if increase ? max 10%, him on the map, similar in points strange reports type +70%...

[Fedex]

hello, I advise you to study a little bit on the forum before putting his hand to the map you will see that some things will be more clear!

really for those who have good foundations, the forum can? to be useful, but for those who try to understand not ? very simple. C'? some user who is dedicated and good in explaining things, but always in reference to my case, the guides are locked and the cases of maps similar many and few, and little commented on in the substance of the changes. So, not to seem obnoxious and rude, but I find your comment a little out of place, and with a veil of apathy sarcastic.
Frederick

[leandro89]

The Egr, I made it with Time, while the hot start, I did help...
However, perhaps while I was doing the map, I actually ? escaped under the control objective, namely, to make a map to reduce the consumption of trying to give more? torque at low rpm.
Errors in maps such as what kind of? instead, I noticed that where there are more? maps, ECM at the time of confirming, asking me to bring back the increases on similar maps and check there? known of the HORRORS, as if increase ? max 10%, him on the map, similar in points strange reports type +70%...

the similar maps should be changed also, and if you see these errors increases exuberant you need to fix every single map

[frantik3]

the similar maps should be changed also, and if you see these errors increases exuberant you need to fix every single map

exact!!!!!!

[munro]

Hello FedeX...if I can have my say you have to apliccarti a p? of pi?...
I'll tell you a p? of things that I liked them and that you have pointed out the others..
for example, in the lim torque parts by too few turns even if the increase and modest,go from 3% up to 6% more about,I don't recommend you make them so...
in the map that ecm called injection zoned(map1), but that in reality ? a map lambda thou hast increased the values while the v? made in the negative, the descittore and the title lambda..so if ori the lamdda has the value to 1 in order not to limit the diesel you have to give up to 0.8-0.9 of the value and lower the descriptor...
you touched on the soi maps and seen the diesel is laughable that you gave does not seem to be the case...
maps of limitation depending on the map and the maf, you have touched as little as a p? all the rest...
there are other things to say but for now I'll stop here...
however, it begins with the moddare the DW or wide choice acceleration from about 1500 rpm and 50% load then about..then it goes you have torque limiters,remember not to begin to moddare low speed, otherwise the frizza don't like...and remember that these maps have the descriptors in nm...
throw down a draft, and then we see...
ah..what the mod for the hot start??can I have the address please??

[Fedex]

the similar maps should be changed also, and if you see these errors increases exuberant you need to fix every single map

I like... Perfect, you begin to understand...

[Fedex]

Hello FedeX...if I can have my say you have to apliccarti a p? of pi?...
I'll tell you a p? of things that I liked them and that you have pointed out the others..
for example, in the lim torque parts by too few turns even if the increase and modest,go from 3% up to 6% more about,I don't recommend you make them so...
in the map that ecm called injection zoned(map1), but that in reality ? a map lambda thou hast increased the values while the v? made in the negative, the descittore and the title lambda..so if ori the lamdda has the value to 1 in order not to limit the diesel you have to give up to 0.8-0.9 of the value and lower the descriptor...
you touched on the soi maps and seen the diesel is laughable that you gave does not seem to be the case...
maps of limitation depending on the map and the maf, you have touched as little as a p? all the rest...
there are other things to say but for now I'll stop here...
however, it begins with the moddare the DW or wide choice acceleration from about 1500 rpm and 50% load then about..then it goes you have torque limiters,remember not to begin to moddare low speed, otherwise the frizza don't like...and remember that these maps have the descriptors in nm...
throw down a draft, and then we see...
ah..what the mod for the hot start??can I have the address please??

Now slowly I try a little to see everything that you said to me
the addresses are:
from 0EEE26 to 0EEE2A and
from 0EEE38 to 0EEE3C
increasing of 900 points
Grazies