Reading tour IAW59F with FGTechv53

[Rebound]

hi all!
Sorry if the topic ? the state gi? the treaty...
I'm reading an ecu iaw59f m3 with hw023
The cock recognizes the ecu data, but reading takes 50 minutes
Something wrong?
With other ecu this is not a problem ? presented...

I can't even write...it gives an error after the warning "make sure that the voltage is higher than 13v"...my ? 12.48, ? due to this the error?

[cinqueturbo]

hi all!
Sorry if the topic ? the state gi? the treaty...
I'm reading an ecu iaw59f m3 with hw023
The cock recognizes the ecu data, but reading takes 50 minutes
Something wrong?
With other ecu this is not a problem ? presented...

I can't even write...it gives an error after the warning "make sure that the voltage is higher than 13v"...my ? 12.48, ? due to this the error?

With HW under 100 it takes dedicated tool, Over 100 you can use the Fiat tool of the cock in boot mode..
then wait for someone more? expert me since lately I whistles for flasks..

[chicco]

as the time of the reading it seems to me a p? along, with regard to the write to bank you can do this only after you have made the virgin the ecu if not, put it in the boot (at least it seems to me that both cos?), the cock seems to me that rivergini only those above the 100 hw.

[carlo abarth]

the time to read...I read and I write to you with the magpro under 100 without the boot because that is not the piazzolla and just ..stopped a m3 below 100(with the tool 59f) and taken safely with the magpro..ovviamantre after reading integra another m3 with the same number ..::!!!perhaps gallo flaw on these ..anyway take a stabilized power supply and you will see the voltage that is around 13.6 v...if you had added below the 1260 gave you as an error seek key..for wireless voltage below 13v!!!

hi all!
Sorry if the topic ? the state gi? the treaty...
I'm reading an ecu iaw59f m3 with hw023
The cock recognizes the ecu data, but reading takes 50 minutes
Something wrong?
With other ecu this is not a problem ? presented...

I can't even write...it gives an error after the warning "make sure that the voltage is higher than 13v"...my ? 12.48, ? due to this the error?

[cinqueturbo]

Paesa.. quadra him to specified Reading tour IAW59F with FGTechv53
now I understand that with other wheat you can? or could not? do certain operations.. but he is working as a gi? said with FGTechv53..

[carlo abarth]

(perhaps gallo flaw on these ..anyway take a stabilized power supply and you will see the voltage that is around 13.6 v...if you had added below the 1260 gave you as an error seek key..for wireless voltage below 13v!!!)

cumpagn my vir that I gave him also a response to the rooster!!!!!

[cinqueturbo]

(perhaps gallo flaw on these ..anyway take a stabilized power supply and you will see the voltage that is around 13.6 v...if you had added below the 1260 gave you as an error seek key..for wireless voltage below 13v!!!)

cumpagn my vir that I gave him also a response to the rooster!!!!!

Sorry for the knife..

[carlo abarth]

hahahhaah!!!!

[giuseppe1374]

I any case, if you're doing a tour if the ecu is not ? virgin does not write the same, so I have the mounts on the car, or you have to riverginare with tool

[carlo abarth]

do you know that I do not remember if I had riverginata good to recover the entire file to make it the one with the flasks partially cleared!!!I went to****!!!!and me and gone many times as well!!!

I any case, if you're doing a tour if the ecu is not ? virgin does not write the same, so I have the mounts on the car, or you have to riverginare with tool