Vw beetle 1.6 TD ECU Simos PCR 2.1 : opinion map and info addresses

[gimarras]

Hi,
if you have some time and curiosity may give a look at this map of a vw Beetle 16 with ECU Simos pcr 2.1. I do not have the driver for the ECM and not use WINOLS and its driver even then I have difficulty to understand the various maps. I attach ORI and MOD defappata and EGRoff. The car goes well enough, only that sfumazza, and at low (1100 to 1400) has a considerable hole of power that I would like to fill but are not sure of where to intervene. Should I intervene on the map accelerator? To which address can I find it? Also the EGR I'm afraid that is not closed : the set of panettone at the address 1CFEA2 - 1CFF60 must be brought to zero? The limiter rpm to 1D2F38 should be well raised as well?
Thanks

[sisco]

the range of panettone that you mentioned for the egr are to be brought to zero, (if you have a functioning valve to the egr bastanp ones) for the rest of the map I can not help, sorry

[gimarras]

OK one doubt clarified. Thanks and good make.
I look forward to any other info...below guys, I know that it is a ECU is not easy!!!

[fabius8585]

gimarras if you can provide me with the id of the ecu I can provide you with all of the addresses that you want to,I can not download the attachment because I don't have a lot of messages.

[gimarras]

Then : these data ID:
HW CAYAC
SW 03L906023KB
SW Agg 03L906023KB
Plant 1.6 R4 CR td
I don't mind the curves of the turbo pressure ( increase of 100 points). Maps to the address 1C6768 and 1C87CE I do not understand what they are and how to intervene. The limiter torque 1D2FD6 how much you can increase? And especially after luca stanca how to eliminate turbo lag, from 1100 to 1400 rpm and have a ready answer to those rides. Then up goes well. Thanks for what you tell me. The map mod I have bought but I want to understand how to improve.

[gimarras]

What's new? Thanks

[gimarras]

fabius8585, do you have any news?
Other?
I'm stuck , I've done several tests, but I don't want to overdo it with the rewrites of the ECU. If someone could give me a hand...

[gabrielikkiu]

gimarras if you can provide me with the id of the ecu I can provide you with all of the addresses that you want to,I can not download the attachment because I don't have a lot of messages.

hello , the ecu that I put do you by chance know these points, what equivallgono?

181E94
1B2B02 1B2D04
1B728C 1B73B6
1EBDD6. 1EBE1A
1EBE56. 1EBE98

[gimarras]

I checked on my ori and mod. The addresses that you listed are all areas that my preparer has not touched, then, I believe, are maps that don't interest you. I don't remember if I did get my map. If you want you the place ORI and MOD and see the areas that have been changed. I have identified the injection, torque, turbo, limiter, rail pressure, and relative limiter, and EGR. As I told you the car is improved, speed over 210 only that fumicchia and usually beat the injectors at low rpm.

[gabrielikkiu]

I checked on my ori and mod. The addresses that you listed are all areas that my preparer has not touched, then, I believe, are maps that don't interest you. I don't remember if I did get my map. If you want you the place ORI and MOD and see the areas that have been changed. I have identified the injection, torque, turbo, limiter, rail pressure, and relative limiter, and EGR. As I told you the car is improved, speed over 210 only that fumicchia and usually beat the injectors at low rpm.