Fiat punto evo petrol edit the file with ecm titanium help me please

[zaga1]

Hi all, today I read the file of the punto evo my friend petrol with rooster v2,so I tried to open it with ecm titanium but I don't find the driver to get in and edit the map.This file you probably need to cut it to get titanium to recognize me select the driver for? I don't know what are the exact addresses is to cut that to bring it back to the greatness of the original writing to make s? to be able to write.If perhaps someone of good heart, I wanted to help him, I would be very grateful thank you all.......................... I enclose a picture of the reading with the file ori.[Image 2.jpg

[zaga1]

Hi all, today I read the file of the punto evo my friend petrol with rooster v2,so I tried to open it with ecm titanium but I don't find the driver to get in and edit the map.This file you probably need to cut it to get titanium to recognize me select the driver for? I don't know what are the exact addresses is to cut that to bring it back to the greatness of the original writing to make s? to be able to write.If perhaps someone of good heart, I wanted to help him, I would be very grateful thank you all.......................... I enclose a picture of the reading with the file ori.[Image 2.jpg

Guys but I can't believe that in all the forum is not there anyone who knows how to cut the file to get it to recognize ecm titanium????? Anyway help me please not only see no answer

[munro]

in the screen posted in words "ecu data" I read 1.2/1.4 mjt 8v iaw55 etc...
that is a bag of v2?

[zaga1]

in the screen posted in words "ecu data" I read 1.2/1.4 mjt 8v iaw55 etc...
that is a bag of v2?

You listen to the unique driver to be able to enter correctly ? that, however, at the end of the file, I was able to bring it to 448 kb to recognize it for ecm titanium, and I have made the changes and after that reported to 576 kb now it remains only for me to write it and just

[munro]

then you fixed it...better cos?....

[zaga1]

then you fixed it...better cos?....

Now should I just write it to the file, and just, and then I'll know

[zaga1]

then you fixed it...better cos?....

For? me is emerging a doubt...................Now explain to you the steps that I did to cut the file from 576 kb 448 kb in such a way that ecm titanium recognizes this and can I change the file....... I used the program winhex I open the file from 576 kb defining the block as a start of 0 and end 01ffff and practically doing the edit and cut and saving the file to me ? released 448 kb and ecm to me immediately recognized................ then I changed the map and my problem now that I didn't understand how to bring it back to 576 kb as using ecm titanium I went on conversions edit and cut by opening the original file and then in the seconso browse I put the modified file, 448 kb I hold a user-defined, in the first log the beginning I set 08ffff and me ? result 576 kb only that what the ec does not convince me that doing the same procedure with ecm titanium, and even putting another value as a beginning than 08ffff I check the same 576 kb........What I want to know c'? someone who can aiutrarmi to make me understand what is the right value to set as the start to have the file 576 kb just to avoid the blocks of the ecu ??? Thanks to all those who participate in my doubt...........

[munro]

if you do a little research on the forum you will find answers you have your doubts...
time f? s? parl? the same procedure but for the marelli mjf8.....

[zaga1]

if you do a little research on the forum you will find answers you have your doubts...
time f? s? parl? the same procedure but for the marelli mjf8.....

I know that I could find the answer on the forum but trust me, so I tried that failed for this I seek help from someone.........Anyway if you would you do me the kindness you could direct me too ? Given that you know many thanks

[munro]

waiting for a girl and I settle for that....