Edit the message of welcome strumenttazione Ducati Hypermotard

[Dirdan]

Hello all, I also own an mpps v13-v12 I don't remember well, that, from what I have read is used to read the whole of the marelli control unit of my bike.
As a first step, if at all ? possible, and does not require a lot of knowledge, I would like to learn how to change the welcome message which is displayed on the instrument panel. This message I believe that it is connected to the ECU, why? when upgraded exhaust Termignoni, which have supplied the ECU, the message on the picture ? changed. In this regard, I wanted to understand qualkosina in pi?.

If c'? any help or good document I can read to start to understand something, reading, writing, cutting files, that would be great!

Thanks a lot in advance to all.

Good job.

[biela]

? you can read the map and find the welcome message that you have now.

Greetings

[Dirdan]

Thank you, sar? the first thing you do?, the cio? read my detailed Ducati Performance and share it with you!

While starting to read, I was looking for any map for hyper to try to understand something, type the sectors in which it resides, the written...

But at the moment I do not have the permission to download it from the forum and in turn I have found.

? you can read the map and find the welcome message that you have now.

Greetings

[maximumwarp]

While starting to read, I was looking for any map for hyper to try to understand something, type the sectors in which it resides, the written...

Whereas, I am not an expert, to search for and edit the writing, I know that you can use a hex editor to open and explore the original file (type HxD)? if you go to edit you have to be careful to make sure that the new file has the same size as the original (should be 320 KB), and also, you should be careful about the checksum!

[Dirdan]

Thanks, I wanted to say, how well does the mpps for the writing and the checksum, I read on the net that at least for the ECU ducati should not be a problem, but I would like your opinions!
I hope over the weekend to be able to read my ECU DP and start spulciarla to see where is this written!

Whereas, I am not an expert, to search for and edit the writing, I know that you can use a hex editor to open and explore the original file (type HxD)? if you go to edit you have to be careful to make sure that the new file has the same size as the original (should be 320 KB), and also, you should be careful about the checksum!

[maurof650]

If you only read, and then want to rewrite the map does not need to do any checksum. The sw below, you say? to do so, but there are problems.
In the meantime, read the file, but be careful because? it takes about more than 15 minutes, to make the tour or, if you read it on the bike, make sure to have sufficient autonomy of stability? and charge the battery.
Damage not can do if during the process of reading the map, if you are pressing the voltage in the middle of the reading, the writing, however, if they can not do)? not ? pleasant and ? always better to avoid.

[m999]

For the writing, with files from 320Kb read with MPPS, looking around at the address 4C130. Maximum 15 digits... I am the checksum on the Marelli/Ducati do I fix this, and no I have never had any problems. We do not even try to do without, not to risk even to try!!!

M999

[maurof650]

Obviously make the cks all the times that you edit a map? I said that ? need to do the cks in the cases in which you read a map by a control unit, and then write on another unit.

[maximumwarp]

For the writing, with files from 320Kb read with MPPS, looking around at the address 4C130. Maximum 15 digits... I am the checksum on the Marelli/Ducati do I fix this, and no I have never had any problems. We do not even try to do without, not to risk even to try!!!

M999

As you need to do to check and fix the checksum?

[m999]

Obviously make the cks all the times that you edit a map? I said that ? need to do the cks in the cases in which you read a map by a control unit, and then write on another unit.

Clearly, if I read and write a particular file is not needed, if I change fix the checksum.

M999