Failure of ABS, ASR, EBD Alfa Romeo 147 1.9 Jtd 16v 140 HP

[Ivyxeddu83]

Hi guys now I will expose my problem...
last December I bought a Alfa Romeo 147 1.9 jtd 16V 140 cv, as a car I can't complain since? to ****llo mechanic has never given me problems. three months ago, cos? from the anything on the on-board computer are switched on the lights FAILURE ABS FAILURE and ASR FAILURE EBD disattivandomi all security systems relating to braking, in practice, as soon as you overdo it a little with the brake pedal lock will immediately rotate the rear becoming dangerous and unmanageable. I went to my trustworthy mechanic and his diagnostics gave error RELAY VALVES failing to clear even the errors why? from there? I explained his self-diagnosis was not suitable for overwriting. for not having done anything he wanted 50 euro; Sends Me to a electrical repair shop of his trust in an authorized workshop Fiat, Lancia and Alfa Romeo. Also connect them, and after an analysis of about half an hour it appears again RELAY VALVES! they tell me that I have the ecu burnt and that I must replace? they were not sure and they told me to go to Cagliari to The Alfa Romeo that having The EXAMINER could give me notzie pi? detailed. Even here, 55 euro without having resolved anything! The day after I go to The Alpha and I can plug in the EXAMINER. after about an hour in the workshop there was to expect an estimate of 1196,20 euro of the abs control unit since? burnt. The mechanic in the workshop tells me that the pump ? composed of three codes, so if I kept those codes I could repair the car for much less.
Cod. Pump 0 265 224 097
Cod. Unit 0 265 900 051 (Bosch)
Cod. Fiat 51748609
Also for this to work the other 72 euro. A few weeks more? latest I can find on ebay an abs pump with all of the codes described and seen that it cost about 130 euro, I purchased and mounted immediately. from this point onwards, I can say that for the subsequent three months I have had more? no problem. 5 Days ago while I was returning from work on the road just after the bend, I met an ox in the middle of the road, consequently, do not invest in the controls of the machine I have put them to the test since? the car has done several skids for? luckily not ? nothing happened. The next day as I turned on the car light up again these damned lights by turning off all the abs system. Tired of spend without results, I decided to repair my car personally.
I downloaded the free version of *********** and I have to say that ? a program is nothing short of just amazing that being a software with limits I don't know how should I do to get the scan button dtc. I hope I can give a hand to solve this problem of system failures why? I can't leave the machine in this state and I don't want anyone to hurt. I read in the forums and I saw that you are real professionals, thank you for welcoming me among you.....

Ivan

[Ross]

I suggest you buy the sw multiecuscan (formerly ***********), also because, ? true it is that we are in a period of crisis, but at the cost of 50€ per year...

[msport (exil77grande)]

I agree seen the money you spent without resolving anything, I would say that the other 50€ for the sw fully functional and official and other few € for a elm 327 that the manages that you can find also here in the online shop of the forum are nothing in comparison,so you can start to see the situation better.

[bart]

Hello Ivyxeddu83, I understand your situation, and you are fair, as I have lived I...
In my case I think it is just a question of a rel?, only those who ? took load of ripararmela ? disappeared (with my unit), so I had to provide for replacing it...
If you decide to open it, is for? A LOT of attention, why? ? easy to damage the board and the components on the inside.
Also (if you want) make some photos of the stages of repair: might be good to create a useful guide to other "unfortunate"...

With regard to Fiat Ecu Scan, in addition to the license agreement, if any, to verify the ABS you need to obtain the following adapter:
OBDAdapter1.jpg

[Ivyxeddu83]

My fear ? to spend again, and as usual, you have again a failure.
I am writing to club alfa and between the forum I was looking for some question-and-answer something similar to my problem. unfortunately, them, everyone has a say, but honestly technician, I have not found anything, only rumors!
you instead seem different, as I have already? the recommended interface and a software. As I said to Bart, I can attach photos and anything else about this unit since? at this time ? right in front of me. Guys the only hoax of this console ? that does not have screws and so less joints to pull out the card ? a plastic made with a unique fusion you only see solenoids, and a slight glimmer of hope a glimpse of the card but you do not understand how to disassemble. if I explained how to attach photos I send a bit of material on which we may reason Together. Anyway, about the program *********** or multiecuscan I saw that c'? just a test to see if the solenoid valves work or not. for? as I said before, if I have to spend for a program that never helps me, I prefer to let loose; I'm sorry but when I lost my job I have to always accounts in your pocket.

[bart]

...Guys, the only mockery of this console ? that has no screws and much less joints to pull out the card ? a plastic made with a unique fusion you only see solenoids, and a slight glimmer of hope you can see the tab but you don't know how to disassemble it....

For this reason in my previous message I wrote: "If you decide to open it, is for? A LOT of attention, why? ? easy to damage the board and the components on the inside."

...if I explained how to attach the photos I send you a bit of material on which we could reason Together....

To attach images, you need to press below the button "Mode? Advanced".
You extends below the window, and you will see new commands.
At this point, click "The attachment manager".
Will you open? at this point a new window.
Now you need to click on the top right on "+ Add File"
A new window will open and then you have to now click on "Select File"
You then open a new window, and from here you select the folder where you saved the photos and from here you will go to select your file that you want to upload.
Selected all of your files, you will need to click on "Upload File".
At this point you will close all open windows, except the first, in which you will see the uploaded files! The ones to display, you can drag in the lower part of the window.
At this point, just click on "Enter in a line" and then click "The fact" and magic, you'll find your file attachments!
If you follow these steps, you can't go wrong: you see that ? pi? long to write/read that...

PS: I noticed for? that by directly loading the images, the site has the habit to reduce it a lot (and then make them less visible) then you should possibly before zipparle (in a single file only) so that they are not out...

[cinqueturbo]

To me, I've a similar problem and it was the stop switch..from quatro money...

[Ivyxeddu83]

Hi to all
how are you? I hope well!
today, as promised, I did a small report on the ecu I was talking about. I took some pictures since some of them do not understand so well and seems to be blurry. the photo ? targeted to see under the solenoids given them the ecu ? closed the you can? disassemble and as a result I do not know how to intervene. I wait for your comments

[Ivyxeddu83]

I apologize if I have posted the file attachments for 2 times!
As ever, I cannot see the file attachments after them public??

[msport (exil77grande)]

I apologize if I have posted the file attachments for 2 times!
As ever, I cannot see the file attachments after them public??

to this question my answer is that I invite you to read our rules and regulations.