Hi guys, can I know how do you replace the ecu after it opened, what to put on to seal the cover. Greetings, Gianfranco.
Printable View
Hi guys, can I know how do you replace the ecu after it opened, what to put on to seal the cover. Greetings, Gianfranco.
I put the sealant black to engine gaskets,resistant to high temperatures
The cleans before closing
the grey dellaloctite and the same as the coloring !!!
I use silicone gasket wurth grey... great
But the black one to close the cylinder heads and black, and good, and then reopen it later it will be? pi? simple , or am I wrong
Use the black or grey both are both greatQuote:
Originally Written by nero72
I recommend the simple butyl glue, for indenrci the one that is used on the inside of the door panels to secure the sheet of polionda or similar to the frame of the door. The island from damp, never hardens, cut off with little force and without the aid of special tools (can you? also, do not heat) IMHO. I have sealed an aquarium containing oil dialettrico with a PC running set (experiments of Sunday) and has held three years before the smontassi :p!
I put the "black pasta", in short, the silicone gasket high temperature for the motor. It seals perfectly, but I have never tried to re-open a unit to find out if it is pi? easy or difficult compared to silicone the original.
Hello all, sorry if I say nonsense, the black paste is not acidic and will ruin the ecu?
They told me that the black pasta leads the current ? best silicone...do you know something?
can I refute your supposition as to a control unit of a truck if the abs-ecu, in the edge of the cover there was a copper wire that somehow was the link mass, no ? noticed and we closed the unit with the black mastic, we were going crazy why? the light that before was not turned on after that we mounted the whole thing was turned on, the moral of the story, removed the mastic light off.Quote:
Originally Written by sportknight
And not have to spread over the entire card. You put very little and only on the edge of the metal.Quote:
Originally Written by lightning
I used the black mastic, what you use for the glass...
the mastic for the windshield, not the necks pi? however,I want to see when you go to make the changes :D
? a hoax..Quote:
Originally Written by sportknight
Auauaua, do not open it more? I leave it so? and that is it. :DQuote:
Originally Written by sportknight
but before putting the new siggilante,the clean from the old one?
I have deleted the old sealant grattandolo away with a scalpel.... but also a blade of a knife goes ir? that's good!
I don't,usually the old one reincolla with the heat of the engine
the silicone does not conduct current,I did some tests,? a good isolatedQuote:
Originally Written by sportknight
Could go well with the red paste? Compared to the black should only change the resistance to heat.Quote:
Originally Written by V.V.
But the butyl glue type as that of the doors of which you speak, V.V. where you could find?
I found a pasta that is a fairy-tale grey for electronic components aquistabile in any electronics show with a ridiculously low price
the better solution ? the butyl . It does away with ease? and the island like the black pasta. With the heat improves its characteristics. Not ? need to clean to put it why? the butyl the same firm all the leftovers of the old glue. They sell it in strips ? nice for the price.
a question I have always had but which I never removed,that sort of thermal paste that c'? on the pcb of the ecu,should be restored? and if so, how?
what's the use? island those contacts?onon it seems to me,why? I see them uncovered,but...boooooooo
until now I always closed it without thinking,warmed myself again the ecu and via
is used to dissipate heatQuote:
Originally Written by sportknight
so better to restore it?the thermal paste that you put pole cpu of the pc is fine?Quote:
Originally Written by guidotacco
according to me you can? do at least,all the ones made by me a long time have never had problems
even I,ma ? a doubt that I ? always remained