Renault clio III drivers

here is my first story

I have a clio that I had a problem with the elettroguida
point blank has left me ? having essential needs? of the car as I live out of town?
I had to buy one in a hurry regenerated
I am convinced that if I could study it better, I could uscirmene with little
maybe a simple rel? the control unit
omitting this peche I do not have more? nail-to-eat
subsequently there have been a couple of very Small defects
the first and the dipped-beam headlamps not lit pi?
and this momentarily baypassato
the other, and the light of the airbag is not to be pi? via and under diagnosis do not experience the issue
now that I am in possession of both a galletto2 that of autocom
I'd like to know where can I find a guide that explains to me how to attempt the recovery.
ps I also have a collection of software.

if the light ? on the erore try with another diagnosis and jumps out

thanks for the reply but what if ? I would like to know the system with autocom
I look forward to advice

that system you have to do....
autocom if ? active you can do a diagnosis on the whole car, not just drivers....
parts from the opening screen, select auto, and then continues under browse and see you will find drivers select then click on the obd at the bottom right and continue..... read failure.....

ah ok
I thought I had to read the eeprom and having to reset!!
as soon as I try and I want to know
the question ? at this point
what I need the software resetting airbag?

he says the word only in the case of crasch and ep2 if you have failures, you are diagnosis tool.....

Quote:

---

Originally Written by sno74

he says the word only in the case of crasch and ep2 if you have failures, you are diagnosis tool.....

---

stramegaquoto

today I read the error codes, but trying to delete nothing happens
remain
any suggestions
the codes have been read with autocom

post the error codes that you have read and see........

Fault codes

Airbag (Airbag - Troubleshooting - MT/AT) (after the last erase the fault code)

DTC Description
DF072 - front Airbag circuit 1 driver side
- open circuit
- present
DF071 - front Airbag circuit 2 driver side
- open circuit
- present

Airbag (Airbag - Troubleshooting - MT/AT)
DTC Description
DF072 - front Airbag circuit 1 driver side
- open circuit
- present
DF071 - front Airbag circuit 2 driver side
- open circuit
- present
DF262 - Signal multi-speed? of the vehicle
- Error internal electronic sensor
- intermittent

you have a problem on the contact spiral of the steering wheel if the fault is in said open circuit ? normal that you do not erase control connector of the spiral is the first to see the continuity? between the plug and the contacts of the airbag steering wheel....

maybe replacing the power steering or tamper with the devialuci for the low beam ? messed up something on the cables system drivers.

the divert light ? been tampered with but ? created a bypass that tension you have lights only when needed. but for that, I have to check his system. in fact if anyone has the wiring diagram that would be awesome
with regard to the airbag controller? the better the plug, but re-assembling the old elettroguida, before you return it, the problem disappeared suspect it's a problem of codes, of course, still are a layman on the subject

test continuity between steering column and airbag driver, you have a problem on the first and second stage can be proved that spiral cable

with the faults that you have not posted ? a problem of codes but I know that you have broken the spiral contact under the steering wheel..... this when you disassemble the wheels should be straight and the steering wheel in the center, the rule that applies to everybody, not only for renault if you have not respected you have forced the contact to the right or to the left and inside you ? walked only proof that you can do to check the continuity? between the plug and attack airbag if the removal did not have problems of spi drivers must have been something in the assembly of sbaglliato...