Willem on Am29f400BB bosch 7.5

Printable View

29-05-2013, 23:22
invasion

Willem on Am29f400BB bosch 7.5

hi all ..

I have a willem when I try to write the file ori on the memory is written, checked and read normally, however, when then the balance on the ecu and I read on the tour I can read it only in boot mode and basically, when the identify is missing a number on the end.. reading the file ? completely different from the ecu that I have written ..

where am I wrong?

to make you understand of 3 photos ..

I have to select the chip that I have under am29f400 or 29f400? because selecting only 29f400 if I do ID from the willem nn I recognize the chip while with am29f400 recognizes it correctly then skip write 0xFF must be enabled?
29-05-2013, 23:49
legendaryslave

the machine part with the file willem ?
30-05-2013, 08:38
alfajtd

read the file with the willem,

compare it with the original,

write the file ori with willem, read it and compare it with the original...

if everything goes back to close everything and the stain should go in the bike.. provided that the saldaure are-made-of-the art...

or in boot mode, write the original file.
30-05-2013, 10:43
invasion

Quote:

Originally Written by alfajtd

read the file with the willem,

compare it with the original,

write the file ori with willem, read it and compare it with the original...

if everything goes back to close everything and the stain should go in the bike.. provided that the saldaure are-made-of-the art...

or in boot mode, write the original file.

thanks for the support ..

in fact, it was what I thought I do it myself .. on the willem ? everything is ok but if I read it in boot mode from the ecu ? corrupted and the checksum is wrong .. while willem is seen in reading equal to the file ori ..

the welds I've done most of the time, and I have tested one by one .. can any track at this point?

but in programming, I have to plan how to am29f400 right? not as 29f400 simple? because if I set the 29f400 I read the ecu from the willem in a corrupt but writing gives me error ..
I also tried to change the eprom..
me, the law only in boot mode, and when I identify the ecu saw that you're missing a number???

then write makes me all up to the cancellation that puts us out a lot, and then goes into the writing we put so much time and error ..

:/

Quote:

Originally Written by legendaryslave

the machine part with the file willem ?

I have not tried since I couldn't read it on the bench .. usually we couldn't read and write :(

Quote:

Originally Written by invasion

I have not tried since I couldn't read it on the bench .. usually we couldn't read and write :(

nothing is to be rewritten .. re .. re-checked from scratch including welding the same result ..

can the willem I don't have to select am29f400 ?? but only 29f400? yet ? amd chip, and is recognized correctly ..

if I reread the eprom from spicy contains the data but in different positions -.- ...
01-06-2013, 08:13
msport (exil77grande)

Quote:

Originally Written by invasion

hi all ..

I have a willem when I try to write the file ori on the memory is written, checked and read normally, however, when then the balance on the ecu and I read on the tour I can read it only in boot mode and basically, when the identify is missing a number on the end.. reading the file ? completely different from the ecu that I have written ..

where am I wrong?

to make you understand of 3 photos ..

I have to select the chip that I have under am29f400 or 29f400? because selecting only 29f400 if I do ID from the willem nn I recognize the chip while with am29f400 recognizes it correctly then skip write 0xFF must be enabled?

if you have read the rules you know that they are prohibited external links,but if you haven't read it yet, I invite you to do so.
01-06-2013, 08:17
invasion

Quote:

Originally Written by msport (exil77grande)

if you have read the rules you know that they are prohibited external links,but if you haven't read it yet, I invite you to do so.

I had read it but I didn't think that a direct link to the photos posted on a host were banned .. external I meant to placed on a server type imagestacks or the like, or links to other websites or forums.

anyway, as for my problem I know to be of help instead?
01-06-2013, 09:23
invasion

Quote:

Originally Written by msport (exil77grande)

if you have read the rules you know that they are prohibited external links,but if you haven't read it yet, I invite you to do so.

Forgive me but in which part of the regulation (maybe I'm reading that wrong!!!!) c'? that I can not post photos taken with my cell taken from a host ? I was re-reading and I miss it :/ where I have violated the rules
01-06-2013, 14:17
msport (exil77grande)

Quote:

Originally Written by invasion

Forgive me but in which part of the regulation (maybe I'm reading that wrong!!!!) c'? that I can not post photos taken with my cell taken from a host ? I was re-reading and I miss it :/ where I have violated the rules

I don't understand where is your problem,the point is that the forum offers the opportunity to post what you want and if you use the search you will find also written as it is and then if we set 80 messages to see attachments,screen etc, and then you can attach it with an external service that we have put to make the 80 messages?
01-06-2013, 14:28
invasion

I think the problem here is not ? my .. the limit of 80 messages from the regulation ? for the download and request pass attachments " new users are in the group "BEGINNERS" and have limitations, they can view the forum but not to download the attachment type zip,rar,jpg,etc., may require a password in the link you provided if not after having reached the threshold of 80 messages (are not considered in the forum presentation, or messages that are considered by us to be spam to reach more easily the threshold) will be automatically transferred to the group "AVERAGE USER" and will not be pi? no restrictions on download or file rar,zip,jpeg, etc., for the pass you can ask for it in pm to one of the two admin,however the staff can decide individually who do enter the section off limits and who is not,however, even if arrived at the threshold of 80 messages since our aim is to have active users you can download max 3 file ori in the day and ask for the pass of the software contained in the link for a max of 2 a week.got to 1000 posts will flounder' in the group "EXPERTS" unnecessary messages written with the only purpose to reach this threshold will be deleted and the user will be? banned for 15 days."

The limit ? to not download and run the users, etc .., but limit because I have posted 3 photos of a problem that I don't seem a moment too ?
01-06-2013, 15:39
msport (exil77grande)

listen, maybe I was not clear enough,you want to post 3 photos ?
foul, nobody is limiting but you have to be to do with the mode' advanced that anyone can use within the forum,if you have not yet figured out say it, that I try to explain it in chinese, maybe we can understand better.
01-06-2013, 15:57
invasion

No No I Understand.. the other hand, you are the **** ? this ? your home ..amen

I wrote**** .c.a.p.or. If not, it seems so :)