The map informed delta 1.6 mjt

Hi all, I have just embarked on the project to make a map informed for my car,a delta 1.6 mjt 120 cv.After reading various posts and studied some files of quest' last, I started this job...I have to say that the file that now I will post is only a draft and is not complete for the addresses touched is for the changes to be made.I would like to know if I'm going in the right direction or completely off course.I explain briefly what I'm doing:in practice, I'm bringing all the IQ of 90 mm3,I chose this value because some of the maps are already calculated for this IQ and I would like to be able to unlock this amount.The doubts that I have concerning the calculations to be done to establish the new values from entering the columns,I make an example to the address 1c183e or map the pedal I have in the BP engine rpm and IQ, the latter is calculated up to 82 mm3,port this value from 82 to 90 mm3 and the fitting on the second to last value from 8199 to 8500, so an increase of 9.8% in the first case and 3.7% in the last one.I used these percentages for "calcolarmi" the new requests of the couple and I was wondering if the reasoning is correct... In other cases type rail pressure I've updated the BP to 90 mm3 but I left the values gold, since right now they are set already to 1600 bar and modderò as I have "informed" correctly the ecu of the new IQ. I hope someone can give me some information about it and tell me if I'm continuing well studies thanks to all I attach ori and mod (complete)

Nobody has the time to give it a look? Purchase

Quote:

---

Originally Written by giuseppe89

Nobody has the time to give it a look? Purchase

---

Hello Joseph,
you have to paste the file golds that we discussed in the other thread so I don't have the bp changed, and to compare it to.
The ones you attached are both the modified and the ecm does not find the subfamiglia driver

Hello Tranky thanks to Dell's attention,I have attached both the ori is the first and the ecm will not find the driver...I use one of the map is the same but at the moment I can't remember what tomorrow is control the pc and the place...I am also enclosing the updated file which I was working before,but now that we're on that, you know, the map advances has the values clear? I took a look tonight, but I can't find it

Quote:

---

Originally Written by giuseppe89

Hello Tranky thanks to Dell's attention,I have attached both the ori is the first and the ecm will not find the driver...I use one of the map is the same but at the moment I can't remember what tomorrow is control the pc and the place...I am also enclosing the updated file which I was working before,but now that we're on that, you know, the map advances has the values clear? I took a look tonight, but I can't find it

---

without seeing the maps with the driver, it is difficult for me to tell you something.. the map advances has as bp rpm/iq and the values are microseconds in the clear, at least on my edc16 so..
looking only at the 2d known to have the fap active and egr.. right?
I am looking for the maps, advances in 2d but it is a long search...

As what is not said.. the mod you've ruled out the dpf and egr (here also known too many curves made zero, surely you have used some software), but you have bad set up a lot of points.
When various a bp, you have to calcolarti his new relationship in the map to its point of the curve..
You touched on a bp that you don't have tap, the one with a value of 8192 is an increasing percentage, and YOU have to leave it to ORI, you need to change to another bp that has the iq or if they are rpm leave ori.
Regarding well, what touches the system, the question of driver otherwise you leave it crazy!

Which bp are you referring to tranky?I do not recall any bp with that now in mind I remember having to take the bp from 8200 to 9000 and the previous 8199 to 8500. With regard to the calcolarmi of the new values in the map for the new iq, I gave the same percentage of increase that I have on the bp. for example, from 82 to 90 mm3 (i.e. 9,8)I don't know if is correct the reasoning.you how to calculate the new values? for the drivers after you place what use that is to a map that is the same but not my will but not by much information about it but...thanks again

The driver I use is D235_509

Quote:

---

Originally Written by giuseppe89

Which bp are you referring to tranky?I do not recall any bp with that now in mind I remember having to take the bp from 8200 to 9000 and the previous 8199 to 8500. With regard to the calcolarmi of the new values in the map for the new iq, I gave the same percentage of increase that I have on the bp. for example, from 82 to 90 mm3 (i.e. 9,8)I don't know if is correct the reasoning.you how to calculate the new values? for the drivers after you place what use that is to a map that is the same but not my will but not by much information about it but...thanks again

---

On the maps the pedal.you must not adapt just no bp....in the axes you request in percentage and rpm

Thanks errecinque I have already corrected everything I had swapped out the percentage for a iq 82 mm3...I have to learn still a lot hehehe but the map advances nn I just can't find it, I'm doing up and down throughout the file, and if you continue to not see it...but they are values in the clear? Therefore, even in the negative?