Hi guys...I read my Suzuki Swift 1.3 75hp. The file that is read by galletto ? 2mb for? while leafing through it, I was not able to find the area of the maps the pedal. Why?? The file ? correct?
In the attached file...
Printable View
Hi guys...I read my Suzuki Swift 1.3 75hp. The file that is read by galletto ? 2mb for? while leafing through it, I was not able to find the area of the maps the pedal. Why?? The file ? correct?
In the attached file...
Hello, ? happened to me, in these the file that is read from the serial should be 2.5 not 2, for this is missing some maps.
The flaw in the bdm and you'll see that c'? all, I do not trust to write what you read
Mmm, but I found another file (the entire file over the network, from the 2mb that for? shows the maps of the pedal. As you said, I don't trust even myself to write...
I try to make another reading from serial port? It seems to me that the interface would select the WHOLE or TABLES...
the rooster on these must-read file-2.5 mb!
if you have found a file from 2mb ? been read in bdm or serial communication with another tool.
read it with kess, or go bdm with cock
Ps, thanks anyway!
Reread, not in the table, and pulled me out of a file of 2.5 mb....! I edit and I write this? I have not had the time to check for? what c'? inside.....
Well, check if ? to place and write.
Reading time 1 hour and a half?
Yeah, it seems to me 84 minutes... But in writing there is the same? Otherwise, until it ends, sar? a batticuor... AAltra thing. Having the file, 2.5 mb,if you were to crash in serial, you recover in the bdm?
40 minutes in writing.
In bdm, the file that you read ? 2mb
Mmm, so in case of a crash, if I don't have the file read in the bdm, I am screwed? Sorry for the questions, but I am still newbie
If the instrument ? good and there are no surges, no crashes, anyway if you gear with dima and scehidino spring, these ecu you first do them in the bdm that in the serial, if you consider that between reading and writing, it takes more than 2 hours.
In the case of a block, you need to check out a file that is read in bdm, not s? if it is possible to reconstruct it from a serial reading, I've never had the need, and then I have not done tests.
I have the template, has done two readings, and this would be the first to write that should do...In the readings has given no problems...No block, and no fault...Now I see a p? how does the bdm....Straight to open the ecu?
Guys, here is the file read from my Suzuki....Now I need to understand more? in regard to maps and addresses...
This so far ? perhaps what I managed to find...but I'm not sure of the maps Rail...
1046DC EGR
104B86 torque Limiter
10AE6E Injection choked
10D6E8 Limiter
10E8F6 Limiter coppia1
10E91E Limiter coppia2
10E95C Advance injection
10F4C0 Rail Pressure
10F77F Rail pressure Limiter
11069A Pedale1
1107CA Pedale2
11091E Conversion pair
What do you know about us?? Mode? change? How to intervene?
now you're going off topic maybe open a new post.Quote:
Originally Written by Danny
Hello Danny, this obd ecu even if you select a table or the entire always a file of 2.5 Mb you have, I doubt that the files from the 2 mega you were able to read it by obd is usually seen that the sw ir? the town does not recognize the file, you cut it to 2 mega, is recognized and you can work it, of course, you need to re-reverse procedure to be able to rewrite the file is 2.5 Mb. I have written a dozen of these ecu with the tool v2 never had problems with the block.
Hello passionemotori...Reading at the table gave me the file to 2mb, and there were no areas of the limiters/maps pedal...Doing the full instead gave me a 2.5 mb...
? the first time that happens to me this news, I have tried and tried and a myriad of times in both ways, but it always 2.5 Mb was the file, I speak to you with the first tool that I still have the version v50
I don't know...V50 also my...The first reading has made the table and gave me the file to 2mb, the second has made full and gave me the file to 2.5mb...
For another, 2mb, lacked the torque limiters/maps pedal.... :D