Printable View
hi to all I try to help I recently purchased bdm 100 on the baya and I wanted to make reading a bosch edc16u1, but I realized after, have flat instead of having caused something serious to the control unit.
in fact, before I could read it and write to tour with mpps v5 now is not giving any sign of life
? can resume it ?or as I think I burned up the micro
If you put the e xxx in the correct position and does not go 100% to the burned unitQuote:
Originally Written by andrew64
sr exchange the micro to the recovery, according to you,
you can only take a...
when you power where you don't have ? almost impossible to put it back applied...
I when I installed the bdm I tried to read a control unit,seeing that no-one would read it, I tried to invert the e xxx,the bdm was not the mpc, and then I was do nothing
after a few days you probably ? cooled, having regard to all the evidence that I had done that day
the fact is that I tried again and ? the game on the first shot with the bdm
probably the bdm was not installed correctly the first time
try to cool it off even if you use the c'? the problem is that the power takes it from e xxx...
sorry, but why? you have not read directly with the mpps that these are easily?
a strange curiosity? my,if I connect a bosch bdm but use supply through the comb of the control unit instead of the original transformer works the same?
of course, with the mpps read and write, but I was trying the bdm 100che me esra arrived and to my lightness I have not checked the flat and as I suppose goodbye ecu?
you had powered from the power supply of the bdm?
I powered the ecu from the power supply of the bdm
take the ecu w put it on the machine if when you shoot the picture, there are the fans to throttle me know that ? dead the micro damned cable to the contrary before connecting the ecu, always check on the e xxx on that pin out voltage you don't have the wiring diagram for edc 16
of course I have the diagram but my fault I have not checked and made an omelette with micro
you must pay close attention to these bdm clones many have put the units out of use,would scruple xch? not check with tester if ? actually to the contrary.
done and ? the result, the grip on the contrary, the flat where c'? the red wire went to the left of the bdm and on the ecu to the right that I gather that was the opposite of that? pin 1 corresponds to pin 9
Please try again with the external power supply
micro burned go to the safe place it on the machine and you will see the fan on the ball......
gi? tested with a power supply from the comb, but nothing happens
Looking for a ecu from a autodemolitore and the scodifichi,quiet are the things that can happen either through inexperience or vice versa for too much security
resigned you strinato the micro ? as it says in the admin can? happen to inexperience or too much security.....
I think that feeding the ecu from the comb it is almost impossible to burnt myself on a marelli I tried to put on the contrary, the e xxx and not you ? burnt
but maybe I understood right he powered up the ecu by e xxx ? this is what has made burn the micro........
It is, in fact, I can't remember a thing, on manual, c'? written how to connect bosch to an external power supply?
I also scared the first time... and despite all of the seller's instruction I had checked with a tester the pin-outs if they were as I thought.. once you have verified everything had gone as smooth as oil... as said by everyone ? verification by 2 minutes but important, and especially avoid burning the ecu... I'm sorry for you but the ecu ? gone...
in the manual you will find all the necessary instructions are well detailed.Quote:
Originally Written by sportknight
the ecu burnt trust I have seen many people who have used the flat on the contrary, however, is a ecu and do a scodifica and forgive affixed if you need you can ask in the meantime, post the data on the type plate of your ecue if you are into sw hw
sorry can you explain me what is the scodifica?Quote:
Originally Written by frantik3
thanks
e-mail the data of the 16u1 are enough to be found for sure someone you can? help for the scodifica on these ecu do on the ep2 but I in my sw I can only find the total laws of the ep2 and email the file to read......