yep, I read a file into the boot of a 500 abarth with fgtech2 and I jump out the file size 869kb how do I cut for titanium to 832kb
I attach file thanks in advance
Printable View
yep, I read a file into the boot of a 500 abarth with fgtech2 and I jump out the file size 869kb how do I cut for titanium to 832kb
I attach file thanks in advance
I have explained to you the technique on my post of the myth.
however, I am attaching the file cut
coma maybe the write step-by-step here, so remains for a possible future research for other because of the title.Quote:
Originally Written by coma
you need to cut from 00008000 to 0000ffff
so to remove a block 64k bytes starting from the address 000080000
here it is:
go to the men? "tools"
then "conversion"
then "cut and paste files"
open the file you want to trim
starting in a low voice, "user defined"
then in the start box, scirvi 010000
should ridarti a file from 832
attention to? who doesn't ? compatible with scripture with magpro nor with MPPS
the file alien or mpps are 832 but the first area is slightly different.
in short, they read differently.
If you have further concerns, you have to do is ask!!!!
:)
this procedure must be done for all the times that you write by obd the 7.9.10?? if rewrite with gallo v2 or kessv2 official I have to do the cutting of the file? THANKS A LOT!
No,
Used only if you read with Rooster v2 why? otherwise, the Titanium does not recognize the file.
Then if you write with the cock the size must be a whole
Then as I have already? said the file cos? cut not ? compatible with kess and other
but with this procedure I can cut the file read with mpps
I'm not sure but mpps in the boot should read from 832kb but we don't put your hand in the fire' cause I've never tried
I hate to say this,if you can cut it with titanium beginning from 010000 goes to cut the first area that reads the cock that we find in the data,in fact if you cut the area 08000 goes to cut the zeros that there are data that are interested!!
I wanted someone who has done even a read with mpps of this machine to know if with mpps you can? do safely...
With mpps de I'm not mistaken you have to use the file from 832 taken from the data base Alien
then you say that you can only write and not read it seems to me to have understood ....
I advise you to get it into boot mode, you never know!!
say we have the risk of nailing the ecu.... Hypotheses if I can find the file ori I make a mod I advice you to also write in bott I think that your advice was this, I understood right.......
you to understand right,I'm sorry if you are to make it into boot mode read his ori the mod and write,xch? risk??
you're right, always best to read and write with the same tool, thanks for the advice, and for now, I have not yet made the bot mode as soon as I have time, I'll wear them and I feel with the ecu that already? replaced and then maybe if I can not I open a post......
? a stupidagine put it in the boot just balances 2 resistors if you have problems you know where to find me:cool:Quote:
Originally Written by sno74
thanks legendary always very friendly when I open a peaceful we feel.......
You have to buy 2 resistors of 100 ohms for the boot mode....you have to get them welded to the pitches, it's not difficult,just need to connect these wires to comb the ecu to read the micro, there are two +12v=pin 6 and 70...gnd pin 1...k-line pin 91.
you can use this skema I used thisQuote:
Originally Written by msport (exil77grande)
Thank you seems such an easy thing now, I saved the pattern as soon as I need that I have to make a we feel....
Hello all,
I didn't understand a thing...... if I read it in your boot with galloV2 an abarth I get a file on the pi? great for ecmtitanium....right? so I have to cut it, but I don't understand if the address 08000, or from 01000......
and when I'm going to rewrite it? assuming that the rewrite with galloV2? I have to reincollare the part of the file?
Thanks
if you read and write with the cock, you don't need this technique to me ? served to calculate the cks with the titan as I didn't know if the fgtech the estimates in writing and I had to compare it with the other files at my disposalQuote:
Originally Written by Emanuele54
however, you have to cut from 00008000 up 0000ffff in hex
but if I have to read an abarth with the galloV2, the file that I read that from what is understood is larger, if I put it in ecmtitanium, it recognizes it and I can change it, or before I have to "cut"?
and once you've finished the mod I have to put them together before you write it? in that way?
where can I see the file sizes of the various cars?
and the method ? the same on all cars?
Thanks
you have to cut it to use it with titaQuote:
but if I have to read an abarth with the galloV2, the file that I read that from what is understood is larger, if I put it in ecmtitanium, it recognizes it and I can change it, or before I have to "cut"?
after changing the riallunghi and I write with the cock 2 by making him calculate the cks.. (I asked in writing if you want to calculate)Quote:
and once you've finished the mod I have to put them together before you write it? in that way?
I think that goes well on all bosch me.. at least the smart 1000 benza.. same procedureQuote:
and the method ? the same on all cars?
ok but if I cut, how and what do I have to reincollargli?
Thanks
Guys but you are confident with completely addresses that you have written?
I have to cut from 0x8000 up to 0x18000, around 10000 bytes.
Use "010 Editor" that has a perfect function to cut and insert bytes.
If you take a file ori bed with a Cock and a file that is read with other tools, you will see that the Cock between 0x8000 and 0x18000 fills only with FF.
Everything you need to remove(and then rimentere).
But not from 0x8000 up to 0xFFFF as written above.
the technique described above, I have experienced the most times you have to cut from 00008000 up 0000ffff in hexQuote:
Originally Written by LucaGT
I am attaching two files ori. One 832kB and one from 896kB.
If the mo cut as you say, I get a file of size 864kB. Can not go.
The file with 896kB have a size of 917'504 bytes
The file with 832kb have a size of 851'968 bytes.
The difference of 65536 in decimal, Hex are 10000, just what you need to cut between 0x8000 and 0x18000.
is the file in the way you cut goes wellQuote:
Originally Written by LucaGT
I know that it's okay, because not cut. Are read by two different tools, and the files are original.
Now I am attaching the file above from 896kB, but cut my way (equal to 832kB).
And I am attaching the file, cutting way discritto from you, which comes out of one of 864kB.
LucaGT I'm sorry, you're absolutely right, the file must be cut from 8000 to 17FFF
Uses a particular command on the 010 editor? I am using hxd I deleted that part by selecting it, then how do you restore it before you write to?? :/ How do you with 010?Quote:
Originally Written by LucaGT
I have a file to cut ? a myth read in virtual redcon galletto v53 and if cut from 080000 to 17ffff m from a file by 864kb who I can? help to cut it or at least to let me know how and what to go to cut the frame to resize it
email the fileQuote:
Originally Written by Emanu88
Now I'm with the mob as soon as I connect with the pc the place
here is the file cut to 832kb, you should do the council not to write by obdQuote:
Originally Written by Emanu88