Printable View
Therefore, after the time that we follow the passion for this world of tuner ? increased to such an extent that he decided to do a spending spree buying a wingnut exactly this FGTech Galletto 2-Master BDM-TriCore-OBD I ? arrived in these days I have installed the soft driver and I went to read my ecu and everything finished with success, I ask, can I post the file to have an opinion of that map I have made and help me understand how to modify it to my liking?.
Thanks and I hope in your help.
hello,according to me you can post to, you will definitely have opinions to your map and some advice!!
Ok sorry, explain to me how to attach the bin file.Quote:
Originally Written by motorsport
use the search that you find the guide posted on the forum for how to attach the file.Quote:
Originally Written by antonio.o
ok I will try I hope I don't mess around.Quote:
Originally Written by msport (exil77grande)
I give you an advice, please contact the online store, no offense, or wait for some expert to give you some advice.
In the map you touched a little, and that little is also bad, the turbo cos? fact according to me you play it...opening the valve, leave it or...
Watch I am a beginner...but you see by the km ? all busted up.
You forgot to attach the ori...
hello antonio if places and also gold. let us give you a conziglio?
you touched on a little, and, even without policy begins to increase a little injection give it a try and as it touches the rest of the torque limiters to the turbo and its limitations, just trying to understand where you're wrong if you increase a little at a time, and try every time you don't do damage!!!!!!
in fact, if you find any of the files example around can? begin to take the idea,so the pu? move on and figure out what to change,I believe, by studying a little out of the results!!
OK I try to attach the ori just wanted to say that the map I ? was made by an offcina alpha.Quote:
Originally Written by panterargento
think about the good days f? I ? route the turbine has started to whistle a little after I have rebuilt the map.
And who knows? how much you have to spend for that job))))))
Hello I ask too much of me to understand with the ECM how can I include and exclude the valve I am just at the beginning and then are totally ignorant of the changes.Quote:
Originally Written by panterargento
Thanks
Fortunately I was able to get it for free why? them bought the car.Quote:
Originally Written by frantik3
Hello.
Are you sure that you ? route?Quote:
Originally Written by antonio.o
Have you replaced?
Those turbines a p? whistle them, especially in the cold...
I intend to work for free in the map, then to the turbo ? another chapter in the stormy, but then seems to came to a happy end.Quote:
Originally Written by antonio.o
You've seen it with my own eyes post completely sliced.Quote:
Originally Written by panterargento
Port to 0, these addresses: 1C4B6E to 1C4B84 then 1C4C3A to 1C4C50 cos? you'll egr closed electronically, then after this operation, you can also close physically with a flange.Quote:
Originally Written by antonio.o
To bring it back to the ori selections the two addresses and click on the button in the top right that has an exclamation point in a red semicircle.
If the map ? still, my advice ? to lower the turbo 60-70 points and put ori the map in the ecm (I speak of the titanium) calls "a Percentage of valve opening".
One other thing, the turbo in that way you could keep (though still high) only if the car ? without the precat and dpf, so what? not to generate back pressure with consequent rise in the temperature of the same.
Hello thanks for the tips but still not s? well or not at all how to move with the soft floor the floor there is going to be.Quote:
Originally Written by panterargento
Thanks.
Hi sorry but can you help me understand how to move with the ECM to find and change these values.Quote:
Originally Written by panterargento
Thanks.
Maybe I should not ask but I would like to understand something hello.Quote:
Originally Written by antonio.o
Then load your map ori in the ecm, load the driver, then open in 2d mode? motorola 16bit, right below where you wrote "go to" add this address 1C4B6E by sending, restrict the horizontal zoom to 160, then the vertical moving one step to the right, remove the check mark here +/- if c'?, select the two contolli from 1C4B6E to 1C4B84 then 1C4C3A to 1C4C50, then take a look at there st? a "m" tiny st? to indicate the minimum value, click on it, and you'll have closed the egr.Quote:
Originally Written by antonio.o
However, I am attaching the map with egr off, cos? when you reach to the useful messages, you will have a better understanding.
ok, thanks for? for a non-expert like me ? hard to get to 80 ms.Quote:
Originally Written by panterargento
I learned qu?, and I'm not an expert...far from it.
You'll see that there arrivals...;)
we are able to close the egr thanks to your help.Quote:
Originally Written by antonio.o
hello people m id? a hand to remove the fap control on this machine.
Here is your file with egr off and dpf off... don't ask me how I did it why? I used ecusafe2 to remove the management...scorrilo in 2d and see the differences...it works for me because I have your same car, but the 150 hp.Quote:
Originally Written by antonio.o
thanks you have been ultra polite for? unfortunately I do not have the permission to download it, maybe in pm nothing?.Quote:
Originally Written by panterargento
Quote:
Originally Written by antonio.o
It is ok as a beginner I apologize if maybe dare something not adjust for the fap to help me understand with the ecm, such as addresses?Quote:
Originally Written by panterargento
there is no need to send me any pm you know very well the rules otherwise I invite you to read it, also I want you to remember that we are here to help as we abbiamno done with you, but not to post the jelly is ready, otherwise, instead of sharing we can call it free jobs,today, it's easy to delete the dpf and egr on a edc16 c39 if you are not capable of asking for info, and you get where they arrived well as completely other with a bit of good will if you do not want to make even a small effort well in that case there is the service of files on-line forum and you pay the person doing it's job,I hope I managed to explain.Quote:
Originally Written by panterargento
the reasoning and perfect from the outset that I do not do trade, and the pure passion that I dedicate fully to my time ****** in fact, I always kindly asked to understand the address.Quote:
Originally Written by msport (exil77grande)
Originally Written by panterargento
I do not think the regulatory...try to send a pm to msport and see what it tells you, if I authorize it, then not c'? problem, otherwise you'll have to wait for the helpful messages...
It is ok as a beginner I apologize if maybe dare something not adjust for the fap to help me understand with the ecm, such as addresses?
I repeat, I have not done manually, I used another sw for the management of fap, it would be very difficult, at least for me, to explain how to fix all the controls...then I have aspects that some expert will give some advice, or you trust the online store...look I what I can do and I have already? exaggerated postandoti the map, and rightly so c'? the people who work on this and the f? x craft...Quote:
Originally Written by antonio.o
I got it, but saw that other than me no one ? stepped forward to give him some indication, I thought I'd help him a p? how could I...all quQuote:
Originally Written by msport (exil77grande)
it is thanks to the soft alternative maybe I know them but the desire to understand ? so only believe me if I need maps 100% reliable definitely, I address to people who are experienced, and then to the on-line shop .Quote:
Originally Written by panterargento
hello
I do at least understand the 2d addresses to check, it was only this that I wanted to.Quote:
Originally Written by panterargento
hello.