Hi,has anyone ever tried to get in diagnosis after the dpf off and the diagnosis witech fiat throws you out with an error
As if it doesn't recognise the car ke and without ddpf and throws you out...
About panda mjet 75hp 8df
Printable View
Hi,has anyone ever tried to get in diagnosis after the dpf off and the diagnosis witech fiat throws you out with an error
As if it doesn't recognise the car ke and without ddpf and throws you out...
About panda mjet 75hp 8df
the luca stanca and' manual or how?Quote:
Originally Written by FidodidoTuning
You switch
well, then it's strange,but if you put the file ori?Quote:
Originally Written by FidodidoTuning
I have not been able to test a perk, the customer had the**** shit from the rush
I think it is a bug of witech,with other diagnoses definitely does not
ori did not,I had made before the zero-coupon
I would say try it with the file ori if he does it again in case the test with a different diagnosis then you can go ahead because of this we are not sure that depends on the file.
A similar problem also with SIMOS PCR 2.1 of the VAG group. after dpf off,pu? happen that the diagnosis not be pi? to read the errors,even if the
that eprom assemble simos pcr2.1?? infeneon tri core as the edc17???
The dpf off and made the switch?anke the prc?Quote:
Originally Written by fabioefra44
the processor ? always a INFINEON,but in the boot making only the release of the processor,then writing the you can? do by OBD. For the DPF OFF,not c'? the single switch as the MJ8DF,but there are more? areas. in fact, the problem of not reading the DTC after DPF OFF ? just what,as contained in the areas to be put OFF.
evidently, are also disabled the dtc...
*fidodido cos? the prc??the motherboard??
capta often that some soft on certain files disable all errors dtc.
SIMOS PCR 2.1 of the VAG group ecu siemensQuote:
Originally Written by munro
ok..I thought that the prc was something else....
In fact, the problem is different,you hainlo the same problem of the vw group, edc16 ke often ecusafe and company elimjnano the whole area dtc,and if you peel off a sensor, not the vwde and do not know where the problem is.
In the prc ke I know c? anke them the off switch for the dpfai
you give me problems happened to me too I had to put the ori
Not c'? the switch-off,you f? manually. In edc16 there are no problems for the fap,at least not to me,they are quiteQuote:
Originally Written by FidodidoTuning
Solved the problem of DTC,all working perfectly with DPF OFF,found the problem with errors in diagnosis.Quote:
Originally Written by nuovaecu
Yes, I know ke ec of the solution on edc16 with switch
But we are going off topic
Who are you referring to?Quote:
Originally Written by FidodidoTuning
However, the prc simos c? the off switch for the dpf
Returning to the title of the discussion my lroblema and ke within in diagnosis but I can't view the parameters me and throws me out,my problem is not c anything to do with the address of the dtc errors...
2 are on the streets or forgive gold and controls if you enter or try with another diagnosis
However, I tell you that ? the only switch-off,then you see a p? you and then with regard to the errors,really depends on the dpf off the fact that you can't see them,in fact I understood what was the problem,now with dpf off you can see the dtc in the diagnosisQuote:
Originally Written by FidodidoTuning
in fact, you don't understand,re-read from the beginning
my is not a problem that I can't see the dtc errors in diagnosis
I do not even see the temp water in the parameters,not in errors
I hope I explained...
fabioefra44 his problem is not ? that fails and does not see the errors your problem ? that throws him out of the diagnosis and does not display the parameters at least so I understood
but in the end you have tried to restore the backup ori?
ExactQuote:
Originally Written by legendaryslave
The original diagnosis of a quiet...
then something wrong
ah here then the problem is 100% in the luca stanca,you have to do is post ori and mod for further advice, otherwise we can end the discussion here.Quote:
Originally Written by FidodidoTuning
In fact, it was a p? that was discussed in the file luca stanca
However, it was what they talked about. Pu? happen not to have errors although there are,but evidently the case in question,if the dpf off is not v? well might not even enter their diagnosisQuote:
Originally Written by FidodidoTuning
and happened to me too
You get error or communication does not find any errors in the ecu... Cm after the avoidance of the dpf is normal that the codes are obscured... If the machine has problems, you should always replace the file cn dpf active to solve, and to recharge those with dpf off
The machine has no problem
I just wanted to enter in the parameters to see if it was changed ****s jntn asamento or preparation
But as soon as I press on the window that should open up the various parameters throws me out with an error.
Have you tried with *********** ? maybe with that you can enter without problems
happened to me; the examiner could not pi? to enter the diagnosis, but with Texa Axone everything was ok and I could see all of the operating parameters.
you confirm,? a problem of the examiner,saw ke changes the setting is in conflict and throws you out
instead, with a diagnosis generic enters quietly
exact.Quote:
Originally Written by FidodidoTuning
in fact, with the texa in the item construction does not give me more? with DPF, but only with lambda probe.