The problem with the map Alfa 159 2.0 jtdm 170cv.....P0402(air flow rate too low)!

Hello all,
I have mapped a alfa 159 2.0 jtdm 170cv, the car v? well and responds well!
I report an error in diagnosis P0402(air flow too low) and the light sometimes comes on but not from others but also turned on, the car responds well......I have now also verified by manual errors, obd and I found that the cod P0402 corresponds to "egr flow excessive" at this point, I ? come to doubt have ended badly the map of the egr....can you give me a hand and check the file if what I did ? correct?
I also looked at your guide to the exclusions egr (for edc16c39) but the screenshots I do not match!
I have even disabled the dpf with ecusafe, tell me if ? done in the proper way or if I have to apply that change on the bit from 1000% to 0%?

Tell me also if the problem comes from another ? the first that I have come across!
Thanks

Quote:

---

Originally Written by Emanuele54

Hello all,
I have mapped a alfa 159 2.0 jtdm 170cv, the car v? well and responds well!
I report an error in diagnosis P0402(air flow too low) and the light sometimes comes on but not from others but also turned on, the car responds well......I have now also verified by manual errors, obd and I found that the cod P0402 corresponds to "egr flow excessive" at this point, I ? come to doubt have ended badly the map of the egr....can you give me a hand and check the file if what I did ? correct?
I also looked at your guide to the exclusions egr (for edc16c39) but the screenshots I do not match!
I have even disabled the dpf with ecusafe, tell me if ? done in the proper way or if I have to apply that change on the bit from 1000% to 0%?

Tell me also if the problem comes from another ? the first that I have come across!
Thanks

---

hello,I start with the egr valve is seen that the main problem is that,then, this being a edc16 let it be the map that the titanium called the egr duty cycle and then return it ori and to exclude the egr port to 0, the two panettone from 1C6A52 to 1C6A64 and 1C6B84 to 1C6B96,then I understand that you want some opinion on the map and then proceed because usually I stick only to what is asked then:
the map torque limiter according to the ideal conditions falla equal to 3 maps of the required torque during acceleration,then the two maps called limiters torque on the motor shaft you have to leave after the mod,then the maps leakage turbo abassale as increases keep yourself up about 150-180 points,then some of the maps turbo pressure are put ori and the pressure of the rail you have to lower as well, keeping a maximum increase of 4% to 5% same thing for the limiter,for the rest there would be more to add, but you have a the basis for starting.

I confirm that I leave it in that map that pertain to all the egr and you will not have problems!!!

...mod you made, what do you say?

Good day to all....
you tell me if the changes are good? I've done in the correct way? I have to make of the other?
Thanks

now the egr ? properly closed, hello

...then shouldn't I be more? have that error? the other parameters are fine? can I try it to write?

sorry if I answer only now, but today has been and is still a tiring day,then now could go,egr ok but let's say that it is quite soft and that is not really the best but it could go,the only thing that I still like are the maps turbo pressure as both increases and as the maps because there should also be times of an overboost between your mod and then call ori and then you should give an increase in fixed-pressure turbo, or about 120 to 150 points, or 4-5% of which is better, how did you mod you.

Hello thank you for the help, at the moment the problem seems to be fixed, look for confirmation tomorrow by the customer .. as for the map itself (such as teaching to the next) and pressure from the turbo as I can I mod and you the place but the time of an overboost from where I see them? I am in the driver I have? I have to try with another software?

Thanks

I recognize them to the eye of the maps and, of course, from break.

....here s? that you should give some advice.... I too would like to come to a knowledge of the cos? high of this field! but the time and the work s? I premier?...! this map if you wanted to make it more? bad what do you advise me?

Thanks