Mjd8f2 file 2049kb or 2048 kb

Hello I explain my problem and doubt. I have a Panda of 2011, an old body, but already with a 8f2.a visa that has already been mapped, knowing of the virtual read I downloaded a file from the database http://www.professionalchiptuning.ne...6&d=1345707541that is 2049kb. With the rooster I have read in virtual and gives me back a file to 2048kb. Now assuming that the database file is read with kess (I also own one) that has the ability to separate the files in the micro and the flash, what should I do? That is, if I want to write with rooster ok I edit the file directly by 2048, and I write, I think, while with kess as to be written? I have to separate and then get together to write or I can write the flash without touching the micro ?Thanks

Ah, and then I'll ask you since I have never written this.... It is better to line the can or K line?

I don't think that the panda can do it in the can, I read really (no virtual) with the kess and the made the k-line and the file and 2048kb, my advice and read it really, then you do what you have to do the rewrite, working on the read file directly.

The.file the injectors read on the can (this is the only way you have the tools available) , but then it has not done me the ecu id gave me a hw error, and the output I selected auto-6f3....bohh

the right file is 2048, if the cemtralina is not communicating on the can, you have to farlaùin kline tranquillamwnte

Aside from the speech, kline can be seen that I have already answered exactly dragus, I have done a punto evo with a 8f2 read with kess and the file was 2048 KB...
If it's the first read/write with kess will ask you to press the clutch and start the engine before completing the read/write with the cock, I don't know why I never tried.

it is correct, is used to recode the sensor on the clutch pedal, the cock-of-date does the mj8

I caught surely a hybrid ecu because on kess the engine code does not match the booklet, there is under mjd8. Tomorrow I'll put more data in, so that you can advise me better. Then the file from 2049 is read in jtag?

I've never made a 8f2 a tour so I could not tell you with accuracy, for curiosity I downloaded the file and tried to open it with the ecm and I recognize a driver and then the file on the database I believe is correct.

This to me is recognizes this and also recognizes that by 2048 the bed in virtual cock with the same driver, but if you have loads for comparison tells you that you must align the x different sizes. Does anyone know how to cut by 2049 and 2048?

Quote:

---

Originally Written by Errecinque

I caught surely a hybrid ecu because on kess the engine code does not match the booklet, there is under mjd8. Tomorrow I'll put more data in, so that you can advise me better. Then the file from 2049 is read in jtag?

---

You Errecinque the "Rooster" returns a file 2049Kb bed in the jtag 8Kb eprom

Here, but why is someone able to read with kess when it does not give the check of RD??

Quote:

---

Originally Written by cinqueturbo

You Errecinque the "Rooster" returns a file 2049Kb bed in the jtag 8Kb eprom

---

there I'm more inside....does that make sense??? How do I get an eprom and 8kb if the flash is 2048 kb? Tell me please the best why do I have to understand. Port patience

I time ago I read a panda with the same ecu (Kess) gives me a file of 2048 kb and finally the reading took two hours.

Quote:

---

Originally Written by Errecinque

there I'm more inside....does that make sense??? How do I get an eprom and 8kb if the flash is 2048 kb? Tell me please the best why do I have to understand. Port patience

---

I do not know the amount of memory available really in the MPC5565, perhaps, has an area otp? booo
the Gallaccio reads two files in the j-tag in one of three ways, All all together,the Micro,Eprom
All 2,057 Kb
EEprom 8Kb
Mic 2,049 Kb

if you want I can upload a Backup

Quote:

---

Originally Written by cinqueturbo

I do not know the amount of memory available really in the MPC5565, perhaps, has an area otp? booo
the Gallaccio reads two files in the j-tag in one of three ways, All all together,the Micro,Eprom
All 2,057 Kb
EEprom 8Kb
Mic 2,049 Kb

if you want I can upload a Backup

---

Ok thanks, saw that the mystery thickens (2 days of news discrepant around the web) , I'll try to open it and let it in jtag and I do bk. Sorry to bother you, just tell me which file goes moddato and rewritten always in the jtag with no surprises. And if you already have then tried to rewrite it to serial if you can rewrite the same file that is read in jtag without cuts and belinate various. Thanks

Quote:

---

Originally Written by lui93

I time ago I read a panda with the same ecu (Kess) gives me a file of 2048 kb and finally the reading took two hours.

---

Thanks for the info, this confirms the kline, which says ugoboss (even if I read the codes inj in the can!!)

Quote:

---

Originally Written by cinqueturbo

I do not know the amount of memory available really in the MPC5565, perhaps, has an area otp? booo
the Gallaccio reads two files in the j-tag in one of three ways, All all together,the Micro,Eprom
All 2,057 Kb
EEprom 8Kb
Mic 2,049 Kb

if you want I can upload a Backup

---

http://www.nxp*****/assets/documents...5.pdf?&pspll=1

http://www.nxp . com /assets/documents/data/en/data-sheets/MPC5565.pdf?&pspll=1
without the spaces.. -.-

there I paste a copy ORI language and English, and a translated to "volemose good," in Italian.. good read

Quote:

---

Originally Written by Errecinque

Ok thanks, saw that the mystery thickens (2 days of news discrepant around the web) , I'll try to open it and let it in jtag and I do bk. Sorry to bother you, just tell me which file goes moddato and rewritten always in the jtag with no surprises. And if you already have then tried to rewrite it to serial if you can rewrite the same file that is read in jtag without cuts and belinate various. Thanks

---

No you can not write to the file j-tag in serial, you have to cut that 1Kb from the end of the file, and then write
You do reason the first one made too, in the j-tag..
but since that tool apple allows and I have no problems to take them again even if it goes wrong "never happened" and open and close them again this ECU is not a walk I always do in the serial..

I also write here saw the post opened by me.

Regarding the marelli mjd8 confirm (I just tried I on a file) that if we have a backup in j-tag from 2049kb cut it with the ecm to the address 1FFFFF, and we will have a file to 2048kb ready to write serial

hello, errecinque you can put a photo of the ecu, thanks.

Quote:

---

Originally Written by ugoboss

hello, errecinque you can put a photo of the ecu, thanks.

---

Hi ugo I have the car in hand you will now place the data.
Hw MJ8DFHW00A
SW 9754B187
VER.SW 0087
SPARE 51896812
VER HW 00

Those with kess...and cock giving me
51896812
MJ8DFHW00A
9754B187
8F2.B1H.
0B B1 0719
.8F2.B1...

the sw is different from what I have read on the serial line I, the mine was 9754B287, in any case, I don't understand why you can't read it in the serial.

Quote:

---

Originally Written by ugoboss

the sw is different from what I have read on the serial line I, the mine was 9754B287, in any case, I don't understand why you can't read it in the serial.

---

Watch...in a week we tried again because it is already mapped and I wanted to pull out the file that is there currently and then the cock is not for my case. I understand that I will have to do a reading in approximately 2 hours...if my kess connects (they have also advised me to change the speed and set it to the minimum) . I know.thanks

then the hole in the k-line and you will see that it connects, reads the injectors (not as you say that it reads them only in the can) and then re-enter always (k) to read it takes a while, I don't remember how much, but more than an hour, it is very first, put in a battery to support the machine and the laptop attached to the power supply, and you'll see that everything goes right.