and for sure that you have a chinese as many v53, not to be the jtag there are many of them around!!!
and for sure that you have a chinese as many v53, not to be the jtag there are many of them around!!!
change the date to the pc or use some sw to confuse the program of the cock.
and yet I was sure to have a good one , if you place the photos you know you recognize it ?Originally Written by frantik3
Use a hard disk with xp only (date 01/01/2013) and with only the folders about the FGtech , niennte of pi? ....
Can you think of something else .
Not c'? no one in the forum that personally it has made with the clone ?
then use an external hard drive with xp, connected to your pc, try to put the date is also on the first pc to 1/1/2013
no , the change precisely in order not to create problems , on one I have win 7 and x fgtech win xp
Another question : to make the 7 jumpers (links) as shown from the diagram that I attached , you like them made ? ... performed with the wire or the united with a point of the pond from part to part ?
I would not like do not read both depend on the welding is performed with soft wire ...
C'? some holy light that can help me , I have this ecu on the bench and I have to replace it to the pi? soon .
Thanks !!!
Reassembled the unit , after the fourth attempt to weld not ? changed nothing ! the reading has not even started ...
I noticed that the ecu ? the same as the GM-Opel / Hyundai-Kia / SsangYong - Delphi DCM 3.7 R5F7
On the cock that I have the SsangYong pu? also be done in the obd , what do you say ? the same, or ? better not to try ?
Last edited by msport (exil77grande); 29-10-2013 at 08:04
nothing no even go like this :-(
I've noticed that in my control unit c'? a component smaller than the one shown in the picture in the documentation Fgtech attached previously .
here I attach the picture of my ecu with the highlighted component in the less
Last edited by msport (exil77grande); 29-10-2013 at 21:51
There is a clone with pc-related dks fmw 54 all crap chinese clone ? as is and is not ? for anything at all in step with the version and release of, those ori
54 the chinese or the europeans, a difference of 53 and have the mcu and the other with quality material? different and that works the jtag and do not need? exchange date, and also works on win7!!!!!
The call 54, and then I can assure you that they have now updated march 2013!!!!
My friend li han sent update to September!!!!
I've seen and it works and everything and work protocols added march 2013
that are these :
OBD CAN driver for Chevrolet Camaro Delphi LS3 Read/Write and Recovery, Checksum
New password Tricore SID 208 Ford - Land Rover
OBD CAN driver for Massey Ferguson EDC17CV44 Read/Write and Recovery, Checksum
OBD driver for Isuzu Transtron Virtual Read / Write CAN Read/Write, Checksum
New password Tricore Tprot V11 Fiat
OBD driver for Chevrolet Cruze, Captiva ECU DCM3.7 CAN Read/Write, Checksum
OBD driver for Opel Antara DCM3.7 CAN Read/Write, Checksum
OBD driver for Renault Clio, Kangoo, Avant-time, Val satis, Laguna, Twingo, Trafic ECU SAGEM 2000 RPM/RPMT K-line Read/Write, Checksum
OBD driver for the Jeep Compass/Patriot ECU Delphi CRD2.x CAN Read/Write, Checksum
tried the tprot V11 Fiat on a freemont edc17 and made cruze DCM3.7 in serial with reading 2mins and writing 27 minutes!!!!
Write permission
Quote