View The Full Version : Problem EGR Alfa romeo 159 1.9 150cv
Hi to all.
A few months ago I bought a 159 sw used and I mounted on the EGR and the plate to limit (the punctured) the flow of recirculated air to improve the efficiency of the engine, after a few days I noticed that at idle speed the engine was empty and after a few weeks I came out of the motor failure and diagnosis I will report the error to the actuator of the egr but I did not give a lot of importance. Lately the engine I was going into protection and I decided to remove the sheet and I found it slightly dirty coal, but nearby there was also condensation that worried me.
Can I solve this error, and being able to exclude something from the ecu? Or should I get a egr functional?
Hello, the egr of the car and the route so that the unit no longer sees the electrical part, in this case you need to replace...
you should attach the file GOLDS so that you can help, or the loads zippzto, or put the link of the database ori ecu with the same HW and SW.
however, you can try to close it with a plate, everything is closed and try the machine.
The map file on the machine is the one that I have attached. An original file I don't know how to get it... However here on the forum are.
As soon as I can I will make the measurements on the coil of the egr functioning. My seems to have a resistance a little low...
Which DTC are you from'? if the file is good, it may be that you have the power management is faulty, I replace the EGR or disconnect the plug, see the DTC, to delete it from the map and you solved.
the 159 is mounted on a EDC16C39, not a EDC16C9 as written by you.
Hi to all.
A few months ago I bought a 159 sw used and I mounted on the EGR and the plate to limit (the punctured) the flow of recirculated air to improve the efficiency of the engine, after a few days I noticed that at idle speed the engine was empty and after a few weeks I came out of the motor failure and diagnosis I will report the error to the actuator of the egr but I did not give a lot of importance. Lately the engine I was going into protection and I decided to remove the sheet and I found it slightly dirty coal, but nearby there was also condensation that worried me.
Can I solve this error, and being able to exclude something from the ecu? Or should I get a egr functional?
My friend, your map is not only with the egr off, but also defappata with sw type time.
as said by the colleagues, probable power management not working....detach the connector, and delete the dtc..put lamerino and go quiet....
as said by the colleagues, probable power management not working....detach the connector, and delete the dtc..put lamerino and go quiet....
As stated above, dtc shall see very few, saw that they already had a beautiful shaved
I have not seen the file....but I read above that error actuator egr.....
made a lot of with unplugged but I doubt that the empty is attributable to the egr!!!
Sorry, but if you deleted the dtc, the machine always goes into recovery only that, it will have no light
Sorry, but if you deleted the dtc, the machine always goes into recovery only that, it will have no light
No deleting the DTC with its controls do not go to recoveri.
If you delete as well the controls ok.I understood only the dtc
It's gone....in the meantime, to know that mistakes gives the diagnosis should rewrite the ori because the file, which is processed with a Time and cleared all dtcs.
In fact, if you read the msg has never indicated the error, I think.
In fact, if you read the msg has never indicated the error, I think.
I autoquoto......he spoke of actuator egr-sorry I did not seen well. However, the file he posted was processed and has the classic area dtc Pxxxx esplanade.
In fact....for this I have written how do you see the error? Strange...and also gone. ...maybe it will have settled....
For the problem of the egr fails, it seems that I have managed to solve it by unlocking and lubricating the plunger of the actuator. At least these days you are not on...
I even made a test to connect to the place of the egr one pilot lamp of the same ohmic value of the actuator and the strange thing is that it seems that the valve is constantly active to the maximum...
I would not like that on the map has been combined something strange...
The original file I managed to find it and I am attaching, also starting from the original I tried to disable both egr fap... if you can give it a look so as soon as I have the machine I try to caricargli the map if everything is ok.
Between the file of the first reading and the one created by me, there are differences in:
1C7C3C -> 1C7C52
1C8C3A -> 1C8C48
1CBE26
1E3572
1E360E
1E40B6 -> 1E40B8
1FDFFC -> 1FDFFE
to what do you refer?
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.