giuseppe89

hi everyone, owner of a lancia delta 1.6 mjt with exchange selectronic and I would like to clonarmi the ecu to be able to play a little without the worry of damage...the ecu is edc16c39-6.6 D and hw 0281014570,now I was wondering if it was possible to use another edc16c39 in my possession.It is, however, to the accuracy of a edc16c39-5.65 with hw 0281012961 a croma 1.9 mjt 120 hp...I was wondering if you could do it is if there are differences as well, as mine is with automated manual transmission, while the eighth note no.There are differences in hardware between robotized gearbox and is not or is only the software that is the difference?

ugoboss

for the automated manual transmission does not have differences hw in the ecu, I can not say if the colour goes well in your, you can try to put your backup in and see if it starts and there are no problems, damage does not do the maximum must not be in motion.

giuseppe89

Thanks Ugoboss tomorrow, I read my you do I this test. But there are ways to have a list of compatibility of the different ecu? If not a will I be forced to find one with hw equal right?

antonios25

You can clone but hw must be equal to

giuseppe89

guys I have made recently with the cloning but it is not successful,the car is not starting...it was to be expected, however, I was wondering one thing:when I rewrote the whole backup of my ecu to that of the croma told me the software that it is not possible to correct the checksum on entire files so I clicked ok and I went without to correct it.From the moment that I have copied a full backup, I thought that there was no need to correct it because I have not changed anything right?the checksum is correct only when you edit the map?or had to correct in this case?

sportknight

in fact, there is no need, since it gets the chk old

are you sure that at least the hw be the same?

giuseppe89

in fact, there is no need, since it gets the chk old

are you sure that at least the hw be the same?

No sportnight the reference number of the hw is different it was a test as much for, only that I was born in the doubt about the checksum.

sportknight

in reality, the problem does not arise because when you extract a FULL backup from the ecu the file already has the checksum calculated for each file,you anyway, when you have to change the maps, read and write the flash(or micro if the maps are in the micro)and for that file the programmer will calculate the checksum of the eprom does not need to checksum it(except on edc17)

sportknight

in reality, the problem does not arise because when you extract a FULL backup from the ecu the file already has the checksum calculated for each file,you anyway, when you have to change the maps, read and write the flash(or micro if the maps are in the micro)and for that file the programmer you calculate the checksum at 100% and then go quiet,the eprom instead does not need the checksum(except on edc17)

giuseppe89

hi to all guys as they are not able to find a unit in shambles as the forklift I wanted to start a "play" with the my without doing damage...as for my software I do not have the drivers on the ecm I was wondering if it was possible to replace it with the one of a delta, of which I have the drivers on the ecm for facilitarmi the thing, at least for now that I am novice... my number hw is 0281014570 the software at the moment not the memory while the number hw of the ecu of origin of the software is hw 0218014569 sw 1039s29787, among other things, his is a euro 4 while my euro-5. can I write that file into the my?aside from not starting, I can brickarla?I would not appiedarmi hehe

ugoboss

not to make similar experiments, maybe not ruin anything but it is better not to make them.

giuseppe89

Ok Ugo, then I can't say...but if you had an ecu with a code for hw and sw always sourced delta 1.6 mjt can I use it as a truck on my own? Or does it change something? I don't think they change the electrical systems of the car or am I wrong?

Errecinque

hi to all guys as they are not able to find a unit in shambles as the forklift I wanted to start a "play" with the my without doing damage...as for my software I do not have the drivers on the ecm I was wondering if it was possible to replace it with the one of a delta, of which I have the drivers on the ecm for facilitarmi the thing, at least for now that I am novice... my number hw is 0281014570 the software at the moment not the memory while the number hw of the ecu of origin of the software is hw 0218014569 sw 1039s29787, among other things, his is a euro 4 while my euro-5. can I write that file into the my?aside from not starting, I can brickarla?I would not appiedarmi hehe

if you don't like cycling I would not ever......

giuseppe89

Let's say that playing sports is good but now it's a little chilly hehehe guys, but technically, what would happen? You plant the ecu? Just to see

the shiston