View The Full Version : Launch Control 1.3 multijet
Anyone have any idea how to do it? I have asked for a 75hp Ecu Marelli 6JF
Anyone have any idea how to do it? I have asked for a 75hp Ecu Marelli 6JF
No I do not think one can do... but popcorn limiter... even himself with exhaust and gold stock engine I have no idea of the outcome, the fact on the various cars with 160-220 hp
for the launch control are a few to know how to do it and you will not find information around.............
No I do not think one can do... but popcorn limiter... even himself with exhaust and gold stock engine I have no idea of the outcome, the fact on the various cars with 160-220 hp
The Rev limiter know how to do it a little bit. you just have to act on the breakpoint of the torque limiters. The problem is figuring out how to do the launch
good evening rianimo this post because in my opinion interesting and something knows how to do it?
You should try with the damos the rev-limiter based on the speed/gear I believe, and change it.. or to act on the injection timing according to the torque required to keep them from rising more than a certain number of turns.. it is Not a simple thing..
the solution was already posted long ago by me in a post....
Does not work with all software..
I change software to get it to work..
the solution was already posted long ago by me in a post....
Does not work with all software..
I change software to get it to work..
watch five I had no doubt that on 1.3 there was your hand in it hahaha. feel you would be courteous to tell us in that post ?
watch five I had no doubt that on 1.3 there was your hand in it hahaha. feel you would be courteous to tell us in that post ?
If you upload a file, I give you addresses and is already very not?
If you upload a file, I give you addresses and is already very not?
certain indeed it is not enough to thank you
1E8ED2
Enginespeed threshold for launch support (1x1)
Conversion method/rpm
-
0
- 0 4000
1E8ED4
Minimum Fast Shut Down, the permanence time (1x1)
Conversion method/sec
-
0
- 0 2.015000
1D5AAE
TrqIndGear map (8x1)
Conversion method(Gear change)/N*m
Gear change
0 1 2 3 4 5 6 R
- 0 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092
1E8ED2
Enginespeed threshold for launch support (1x1)
Conversion method/rpm
-
0
- 0 4000
1E8ED4
Minimum Fast Shut Down, the permanence time (1x1)
Conversion method/sec
-
0
- 0 2.015000
1D5AAE
TrqIndGear map (8x1)
Conversion method(Gear change)/N*m
Gear change
0 1 2 3 4 5 6 R
- 0 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092 300.0092
Thanks a lot 5turbo today, he looked at the map and see if I come afloat thanks again
hello 5turbo then all address 1E8ED2 c and a decimal value of 4000 I assume rpm to which you want to stop the spins at the maximum of the pedal .
then all address 1E8ED4 a decimal value of 31, the description speaks of the time of stay. what would it be? and that value we need to do?
then 1D5AAE as I understood, each bit would be the march and then the second bit of the limiter c, and the 1st gear it goes moddato?
thanks again
hello 5turbo then all address 1E8ED2 c and a decimal value of 4000 I assume rpm to which you want to stop the spins at the maximum of the pedal .
then all address 1E8ED4 a decimal value of 31, the description speaks of the time of stay. what would it be? and that value we need to do?
then 1D5AAE as I understood, each bit would be the march and then the second bit of the limiter c, and the 1st gear it goes moddato?
thanks again
The dear saviour..
see that no one has told me where to take action, and even less explained how to do it..
then study,test, and you will get there..
"you are already very beneficial to both addresses that I have given to you is that you have all the conversion that you're working on a 8DF"
The dear saviour..
see that no one has told me where to take action, and even less explained how to do it..
then study,test, and you will get there..
"you are already very beneficial to both addresses that I have given to you is that you have all the conversion that you're working on a 8DF"
One more thing if you can't tell me about it the conversion factor for the limiter, and then if I understand I should lower it but after not remain low?
One more thing if you can't tell me about it the conversion factor for the limiter, and then if I understand I should lower it but after not remain low?
I have a file of a point in 2015, which has already been done by the ori . I searched on the map the addresses of 5turbo she gently turned, however, the values are the same as mine. ������
What did you expect in addition to the addresses and the conversion factors??
100 euro and a file ready??
it's okay...
What did you expect in addition to the addresses and the conversion factors??
100 euro and a file ready??
it's okay...
Watch this shot you could just save me in a polite way I asked for and equally educated could answer that I could /wanted to say. Respect all ideas, but rather exposed so not arrogant as you just did. I'm sorry even more because behind a forum are a person well prepared in the scope but that I have “inserted” in your black list I do not see why
in fact .....
a response just a psychopath could simply mean studying and trial and error, or do not directly answer the most....no black list responses on acid etc etc.....
mah that ***** forum ...... and that ***** of people there in the forums have done years and years the dogs on ****** now know 4 things, and you feel ....... in the power to respond as they want, not realizing that they are lucky that they are behind a keyboard, I would like to see the presence respond so ...... from the outset the ***** of forum that I am blocked because some one year ago I unintentionally wrote something that I didn't have to write ... dozens of times in pm asking sorry if I could be forgiven and resume the permissions for the downloads, etc, etc .. no politely no response .. and so they lost a user like so with me and the other 1000 in fact, and a forum little not haunted, but every so often I look to see if you are taking what I read .. crap ........
read the #14 post..
if you know read more than to shoot minchionate..
I gave the address & conversions mo that you want more??
dear carfree in addition to the fact that at this moment there are 100 guests and 17 users on the forum seems dead this forum, in fact it may make less than someone in particular..
without an attorney no one will create useless discussions...... I think 5t is a very good user has given and a lot in this forum and I will stop here..............
a forum dead? hahaha!!but you have on other forums? I don't think that you can find the same info and the same online users.... then you appreciate the aid, and we learn things together........
the solution was already posted long ago by me in a post....
Does not work with all software..
I change software to get it to work..
Thanks.
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.