View The Full Version : KESS V2 MY works 100%
I Kess V2 works 100% on all systems, not included in the truck.
With a small change in the hardware ready.
this change you can' know or do ? only on sale.
this change you can' know or do ? only on sale.
I would like to know, too thanks
Mafani you that fw you have, in the kess?
rodcraft86
07-09-2014, 18:29
? the usual 1.89 as all
If ? correct, hes using the clone
Information for all to read and write IAW4MV the VAG group, you have to unsolder the eeprom 95060.
It can? be done with or Galletto Kess V54
Information for all to read and write EDC15C7 FIAT group, you have to unsolder the eeprom.
It can? be done with or Galletto Kess V54
If ? correct, hes using the clone
but it is small change in the hardware, you may know or not?
You can? say, the problem of KESS v2 with the K-line ? the voltage.
If you select the line voltage source k ? approximately 4.5 v should be the voltage of the battery.
Will try? to make a description of how it works perfectly for us $ 0.30. I upload photos with the change. It's very simple.
ok are waiting for the photos then.
Here, the editing, the photos ? the original, but ? equal to kess clone.
Above all, don't try to put another diode 1N4148, place in a certain sense as the photo.
ok are waiting for the photos then.
ugoboss expect ;)
The v2 24v kess pu? work without any problem. With this change you will see? that the K-line diagnosis works perfectly.
I only hope that I thank you.
Tested with MED17 TRICORE with adapter Tricore.
thanks ecuprom as soon as possible we will try this mod
thanks, even if I still don't have the kess, now we are waiting someone doing the edit and test.
I hope that help your Kess v2 to operate the line K.
This pi? that tested and it works. The line value 12v K works with the protocol below.
-70% Of the supply voltage for the data to be sent.
-30% Of the voltage for the data received.
The v2 24v kess pu? work without any problem. With this change you will see? that the K-line diagnosis works perfectly.
ecuprom I did not understand ,with this change, the v2 clone can also work on 24v? or only the original works at 24v?
? can work without problems with 24v.
But if you have not enabled protocols truck, that the use 24v?
If you look at the power tab kess pu? support up to 30v, but ? fully protected subsided to work after the meal, that ? 5V board microcontroller, as an entire work.
Photos of the line integrated load KL and Can Bus
We are all excited!!! Thank you in advance on behalf of all if you want to share
Thanks to all of you.
Now I put the video that I do the ecu with Kess
ecuprom I can not see where to solder the leads of the diode
From the point where the 2 red lines, ? where you solder the 1N4148
I sent a photo with two red spots, ? where you have to solder the 1N4148
perfect now ? clear.... I'm going to weld thanks
The whole question, please tells me
Oakley when you're done you can make a detailed guide on this site even though I got it right ! And especially as the protocols are activated
nox, therefore, you need a diode 1n4148 look at the photo that he posted ecuprom you have to solder in the pins marked with red dots..not mistake the polarity .with regard to the protocols unfortunately ? a problem of the fw... we don't have the updated one
oakley1, has tested the change?
I have on hand a kess and also the k tag a friend, the two of 1.89 xo on the ktag protocols are all enabled, while when I connect the kess protocols trucks vanish except someone to Renault , then as I understand, however, the change will improve? however, the operation ? The polarit? and that of the red arrow? Thank you very much
not yet, for now, I have not edc15 to try....you ecu have you tested?
the black dash that I designed on the diode matches the indent of the bill... the amendment does not implement the protocols, but it goes to obviate l is impossible not to read the edc15
If you put the diode as in the picture, that ? the polarit?.
You ? tried with EDC15?
S?, I EDC15 test and it works.
ATTENTION: THIS IS NOT 'ACTIVE PROTOCOLS GRAY.
This modification ? to communicate the K-line, line and stabilize the canbus
I put the link video recording EDC15C2 PSA.
Yes I saw but written in the Bench, however, not connected to the car right........
Tested on the bank and drive
ok good I while back I tried with my kess to read this ecu citroen and not read it gave me error alarm clock usually when you do not connect or protocol wrong thanks for sharing........
Have you tried changing that ? set?
as soon as I have time fiaccio the mod to kess I feel I have a ecu in the lab and see if everything is ok..........
rodcraft86
07-09-2014, 22:56
guys I am there to wheel and prover? even I change
Guys, if you change the Kess v2 ? very good tool.
We give great joy to see how it works
legendaryslave
07-09-2014, 23:29
I sent a photo with two red spots, ? where you have to solder the 1N4148
ok soon, let's try this thing thanks to the share for the time
Then as I understood from the diagram did in the photos I have to put the anode of the diode going from the left to the right cio? the black seam of the diode and the cathode in the diode of the classic and the silver, and the line that is going after the scum of the schema correct me if I'm wrong
passion engines
08-09-2014, 00:26
Hello fw 4.034 ? of the tool working ? useless you have a sw agg. that then could not? be usato.........
Quoto in full for all active protocols you have to have fw 4.034 .............
but, in fact, ecuprom said that this change serves to make it work better version 3.99, does not unlock any protocols that are not active, are two different things.
Is real interesting thing would be to update the FW then you could work with all of the open protocols and also the new....
I believe that sooner or later something get?.... You need to? see if the micro is fine or ? to change to the new fw
From what I understand ? the micro needs to be replaced or would it take a save to load and write with jlink clearly the FW up to date and content of the internal SD in addition to the SW that now ? available in the network.....
Good, about 4.034 fw problem if something that nobody say? on the forum, we have to assume that the version 3099 ? the best we have. We must make the best juice.
Version 3099 works with fw v1.89 and v2.06, but with this latest version does not have all the active protocols
You have to try some of the files from the sd to work perfect all active protocols
I do not believe that active protocols depend on the sd card but from the fw
In the sd are the communication protocols.
"The protocols are not sd activation"
I have done many tests with the files on the SD card and not all of them work well.
In nxp protocols activation lc2478 are
The obvious ones are in the micro-and without fw up to date will always remain inactive.
With the rules of the forum I can not put the sd files that work
passion engines
08-09-2014, 12:48
Hello, good tool does not need any change and has all active protocols, of course, nothing to do with the tool that you are just pennies
You speak of the tool or in the original?????....... With the fw 3.099 those are active protocols.....
All clone kess, have the same problem. If you know already? the original works perfect
The fw 3.099 works ? for v1.89
Has anyone tested the change posted by ecuprom?
Then head! With beetle 90hp... Before the change is not identified now reads quietly
It is a pleasure to hear that it works. Oakley1
oakley1 well then forward all with mod...
I am a person that tells lies. I always tell the truth.
Not like in other forums only tell lies
Thanks������ now the next step ? find and prof are the firmware 4.039
Oakley1, who will? pi? difficult
rodcraft86
08-09-2014, 19:53
guys, in the meantime, I'll tell you what I noticed today, the software 2.06 on kess goes well and has some protocol in the pi? but it is only for the kess, in fact, I tried to do the same thing with the ktag, but the protocols that provide the edc16c39 and dense, are all disabled, I solved by putting the kessv 2.06 on xp and the ktag 1.89 on seven
rodcraft86
08-09-2014, 19:54
Then head! With beetle 90hp... Before the change is not identified now reads quietly
good news!! could you post a picture of the change?
Already there are photos read a few posts back............
you how to change not ? nothing exceptional, and it takes the images already posted, I made yesterday evening at the tool of my friend and it works fine,
I wanted to ask a question, given that advise to disconnect the internet when you connect the interface, I thought, but if you make a rule on the firewall not to connect the sw of the kess both in revenue and output, it is not enough to protect yourself from any updates?
my ? just an idea someone has tried.
Ugo, the speech is not a book... But I don't I could block out the interface
gianni1001
09-09-2014, 20:52
Then the change of the diode brings benefits to version 2.06?
guys, in the meantime, I'll tell you what I noticed today, the software 2.06 on kess goes well and has some protocol in the pi? but it is only for the kess, in fact, I tried to do the same thing with the ktag, but the protocols that provide the edc16c39 and dense, are all disabled, I solved by putting the kessv 2.06 on xp and the ktag 1.89 on seven
The amendment allows you to read with the kess the edc15... for a voltage problem to the edit could not read
Hello friends. Who changed that Kess ECU a tested. Greatly appreciate it.
Grcias
carlo abarth
09-09-2014, 23:37
these pieces that you have to implanatre to the instrument where they are!!
Photos of how to do this on page 2
these pieces that you have to implanatre to the instrument where they are!!
? a simple diode, if you go to any electrical repairer of tv and various things I find to Kg.
gianni1001
10-09-2014, 08:44
But I have to use just the heat, or even a common in4007?
For the accuracy 1n4148
Hello ecuprom could you tell me what that component that is missing on kess my friend and I've also seen that compared to the photos that you put you lack the mass connected to the connector hello, thanks
Nox the one posted in the picture ? l official
what is missing on the clones should be a buzzer, something different must have, otherwise ? a casino.
However, as you can see from the photo diode I put it and I just read hiunday tucson edc15c7 yesterday, nn identified with even only thing that at the end of reading has pulled me out of the error cecksum but still has the file and right xke ecm recognizes him peacefully through ecuprom and share
Hello nox. I can't see the photos because? I have enough of pi? the message
Hello if you get checksum errors. And 'why? ? need to install the Visual C ++ 2005,2008,2010. Make the intalacion and really don't get the error
It is also good the v credit 86 as a library
you need to install the visual c++ libraries up to date, that is why it is sometimes said that you need to install the official version before using the files that sometimes give the clone, those portable without installation, installing the ori will also update the libraries, otherwise download and install directly.
Streetracer90
17-09-2014, 21:04
Guys sorry, as ever I have this screen? I have followed all the procedures for the installazione8495
rodcraft86
17-09-2014, 21:26
update windows to the maximum and install visual c++2008 you'll see that it works
Streetracer90
17-09-2014, 21:56
Then I confirm that on Windows 8.1 works?
rodcraft86
17-09-2014, 23:43
no, only win7 and xp sp3
legendaryslave
18-09-2014, 02:11
Guys sorry, as ever I have this screen? I have followed all the procedures for the installazione8495
hague seems to be a hw error
Hello to all, as I work with the kess changed?.
Count me as I work. that work the ECU.
thanks
rodcraft86
18-09-2014, 23:13
tomorrow the balance the diode and see if it works, I've heard a couple of guys that have it welded but it does not work
Maybe they're installing the diode on the wrong way, its just a guess
I put it up and it works on edc15 where, before, instead it gave me error.
yesterday I had a problem, I tried to read a renault scenicII 1500 siemens sid , and after-the-fact data, and have begun to read when ? arrived at the 50% and gave me error in the data transfer, I tried 2 times but always the same, always ? never happened to someone and you know the cause, thanks.
rodcraft86
19-09-2014, 16:56
guys you can put a sharp photo diode soldered? I would not like to lose the sense
gianni1001
19-09-2014, 23:25
What kind of key do you have? The ignition key or classic card?
If the card you put in before, do not touch any pedal insert the card, then press 8 to 10 seconds, the start button without touching any pedal, and the framework does not switch off during the reading.
If it asks you to turn the ignition off, remove the card, and when you turn do the same procedure
Ok?
=ugoboss;100649]yesterday I had a problem, I tried to read a renault scenicII 1500 siemens sid , and after-the-fact data, and have begun to read when ? arrived at the 50% and gave me error in the data transfer, I tried 2 times but always the same, always ? never happened to someone and you know the cause, thanks.[/QUOTE]
rodcraft86
20-09-2014, 01:38
the kess, however, tells you the procedure when you select the ecu and also by clicking on the help button, and explains everything in detail
What kind of key do you have? The ignition key or classic card?
If the card you put in before, do not touch any pedal insert the card, then press 8 to 10 seconds, the start button without touching any pedal, and the framework does not switch off during the reading.
If it asks you to turn the ignition off, remove the card, and when you turn do the same procedure
Ok?
=ugoboss;100649]yesterday I had a problem, I tried to read a renault scenicII 1500 siemens sid , and after-the-fact data, and have begun to read when ? arrived at the 50% and gave me error in the data transfer, I tried 2 times but always the same, always ? never happened to someone and you know the cause, thanks.[/QUOTE]
the fact ? that is not me ? switched off the ignition, everything ? been turned on.
gianni1001
20-09-2014, 07:18
But you have the key to the traditional fly card?
gianni1001
20-09-2014, 07:24
the kess, however, tells you the procedure when you select the ecu and also by clicking on the help button, and explains everything in detail
You ? happened to me
And I followed the directions of the help.
in the help c'? written press and hold the start button until a click is heard as the rel?
The fact ? that does not feel....
If you press and hold the button at least 10 seconds, but you are sure that it will works
For? if not, do the procedure
gianni1001
20-09-2014, 07:25
But you have the key to the traditional fly card?
I wanted to say " ... or the card"
It does not fly... :)
gianni1001
20-09-2014, 07:31
the fact ? that is not me ? switched off the ignition, everything ? been turned on.[/QUOTE]
To me it seemed switched on, there was also the engine light yellow
But really? while the law off...
To me came down to 30% after missing 5 minutes and 15 seconds after which?
Stopped reading and asked you to turn off the picture
? you d? error data transfer...
the fact ? that is not me ? switched off the ignition, everything ? been turned on.
To me it seemed switched on, there was also the engine light yellow
But really? while the law off...
To me came down to 30% after missing 5 minutes and 15 seconds after which?
Stopped reading and asked you to turn off the picture
? you d? error data transfer...[/QUOTE]
then you very likely that it is as you say, the next time I hold it more, thanks.
Information for all to read and write EDC15C7 FIAT group, you have to unsolder the eeprom.
It can? be done with or Galletto Kess V54
can I know where did you purchase kessv2?
ake85 if you want a toll-functioning and assistance ask the shop of the forum they can help you then ? forbidden to post links on the forum by regulation.......
I know it because I asked in the forum but still I do not have responded
Hi to all guys, has anyone figured out how to solve to make it work with the truck and then to 24v?
Ecuprom I read somewhere that you have the fw 4.034 and files to the sd card..... sell them to Me?
gianni1001
27-09-2014, 13:12
I appended to the request.... If administrators allow
Hello I have the fw 4.034 or sdcard. I'm looking for
On another site I read that you had the fw 4.034 :)
megasosio
02-10-2014, 18:07
Any knows a good seller for kess with all activated?
? can work without problems with 24v.
But if you have not enabled protocols truck, that the use 24v?
if I understand correctly ecuprom this change is just to read the protocols of the truck as line 24 volt? or I am mistaken? thanks
This modification ? for the k-line. No truck active protocol. Works on 24v. But, as the truck doesn't ? active protocol does not work.
This modification ? for the k-line. No truck active protocol. Works on 24v. But, as the truck doesn't ? active protocol does not work.
Ok understood...then the change of this diode is used for the line k-line, but it was the EDC15 if I understood well...but if one has both the cock that mpps I think that is not used...you made this change?
This modification ? only for Kess
nox, therefore, you need a diode 1n4148 look at the photo that he posted ecuprom you have to solder in the pins marked with red dots..not mistake the polarity .with regard to the protocols unfortunately ? a problem of the fw... we don't have the updated one
Hello can I know the right size because I find of various voltage and amperage thanks for the reply
Hello can I know the right size because I find of various voltage and amperage thanks for the reply
go by a qualified electrician repairs the tv and things like that and you say give me a diode 1N4148 and he will give you as many as you want without asking it the voltage it amperage.
thanks ugo the gi? got it...this is only for the edc15 or even edc17?
only for edc15, otherwise you get error free.
rodcraft86
25-10-2014, 23:16
so guys, after you have welded the magic diode, I only got the chance? identification for edc15, when I try to read, I always, the WRONG ACCESS CODE, tried it on c2 - c7 - vag edc15p same story for all, the same for other friends who have the same tool, these changes, as usual, is beneficial sporadic and never sure
on my worked, first gave me a communication error, and after I read and wrote several types edc15.
rodcraft86
26-10-2014, 00:09
you have the tool 2.06? or the previous version?
Metropolis
26-10-2014, 21:40
guys sorry for the question maybe off topic, but I wanted to ask I had read a p? time ago that the kess clone after 60 scriptures hangs...? a problem with that ? been resolved, or there is always?
the last when you block them resets with the jlink
lupen115
12-11-2014, 12:30
Hello ? possible to have a guide to re-program the kess clone with jlink.
thanks...
lupen115
12-11-2014, 12:44
Hello ? possible to have a guide to re-program the kess clone with jlink.
thanks...
To sorry I forgot ? can also have the help of the diode on kess.
Thanks and good job to all of you...
112rosso
17-11-2014, 14:33
Hi guys I also have a kess v2 and I would like to do also I the mod of the diode but I can't see the attached photos :mad: maybe I still have a few messages?
I Kess V2 works 100% on all systems, not included in the truck.
With a small change in the hardware ready.
where to find, and more? info....
r6raven2010
21-11-2014, 19:43
today I ? arrived the diode ph4148 or 1n4148 bullet you want to call it you and I just welded... now I'll have to wait for an edc15 to try it... in a week I should get a golf... and I know... hopefully... fingers crossed
r6raven2010
23-11-2014, 20:24
thanks a lot ecuprom... the change has had a positive outcome on my kessv2... today I read and wrote quietly edc15 of a golf...
another question... how can I find the help file ?
you need to download the ori version of the software on the site alientech you download the help and copy them in the help folder that you have your kess!
no one from the directions?
r6raven2010
25-11-2014, 20:03
I have downloaded the software ori but I open the help file... do I have to connect my clone? not c'? the danger that I block everything?
all you need to install an old version , I think the 1.89 and in a clean pc where you never put another version.
r6raven2010
26-11-2014, 07:54
The site is download only 2.06... 1.89 where can I get it? If regulation allows nn you can share the folder help?
112rosso
26-11-2014, 14:19
Hi guys does anyone know what it means to "wake up" my kess v2 reads almost nothing
112rosso
27-11-2014, 13:24
Wrong links I don't think why? I connect it via serial from do not tell me that ? to throw
then the mistakes, the model of the car! senn? I repeat ? you can throw away! the joke, however, I have heard around that many had this problem and have it sent back in for service
Also my on kline sometimes I d? error / alarm clock!!!!
I want to try to put the diode and hopefully go better!!!
michele30
01-12-2014, 21:48
Raga, I will not write the iaw59f tells me to change the write speed , but the setup does not give me the option to change the speed, but only the pull-p that I don't know what it is.
Do you have any info ?
fabiovts88
04-12-2014, 21:19
have you ever written to the ecu of the alfa mito tjet or 500 abarth bosch me 7.9.10 with the kess v2 clone serial?
sure it's fine, no problem.
fabiovts88
04-12-2014, 22:52
Thanks hugh for the info
vr6-killer
05-12-2014, 13:07
Dear Ecuprom!
I would like to ask you to send me a photo of the PM, I also know that over the kessv2 was established, I have a problem with the K-line operation. 1N4148 diode is, but I do not know where to solder. If I understand correctly, you can join this transformation 24V systems without damage if there is a fw modules which are active in the trucks.
THX!
Best Regards!
vicius_the_one
10-01-2015, 02:31
Forget about diode solution. it is a hammer mod solution. don't you realize alientech designed a very good pcb? does it really needs to worthless diode to help it work? no, of course not!! this is intoxicating info people! unuseful!!!
the problem is not the absence of tht diode!!! the problem are other parts. i have just fixed myself my clone with parts of 0.7$.
I also tried this Diode mode and it was worse with it.
Stop intoxicating yourself reading above. it a lie.
Forget about diode solution. it is a hammer mod solution. don't you realize alientech designed a very good pcb? does it really needs to worthless diode to help it work? no, of course not!! this is intoxicating info people! unuseful!!!
the problem is not the absence of tht diode!!! the problem are other parts. i have just fixed myself my clone with parts of 0.7$.
I also tried this Diode mode and it was worse with it.
Stop intoxicating yourself reading above. it a lie.
I tried it and it works great with the diode, but if you have another solution why do not you say, so let's try.
vicius_the_one
10-01-2015, 07:47
I didn't say it not working. I said it is a hammer mod solution that was not figured out by designers of the pcb. It is just a way to force the pcb work but not as it has to be. Problem are in the group of those eleven sot23 transistors. When I put diode and it worked even worse. After change the transistors everything works fine. I need to close detailed picture of the area with those 11 transistors so I can read their mask
vicius_the_one
10-01-2015, 07:49
I was frustrated because all forums insist with this diode solution that is not very good. It is like treatment from the symptoms not causes for.....
vicius_the_one
10-01-2015, 08:00
For example before I fixed I could read edc15p only at the minimum speed in that way, ate 5 6 tries. Also dacia logan 1.4 Mpi sirius32 could not even identify the ecu.
Now it reads write edc15p and sirius32 at normal speed from the beginning. It doesn't stuck anymore to make the restart process for reading or writing
vr6-killer
12-01-2015, 08:37
THX...!!
Does anyone know exactly what you need to improve the pcb?
franco75
12-01-2015, 10:07
a friend of mine has soldered the diode and now more error alarm clock, we tried it on a Megane 1.5 Dci with the Ecu delphi.
Before the diode gave error alarm, now it is correctly identified. Before the diode gave a voltage of the battery is always low, less than 11.8 Volts, now with the diode from a voltage higher. Actually ? unthinkable that there is an error in the design, maybe the diode compensates for any low voltage caused by some component that is not appropriate
vr6-killer
12-01-2015, 11:22
Dear friend, thank you for sharing your experience!
clabsport
21-01-2015, 00:29
Waiting to download from the forum to try the change. :(
vicius_the_one
21-01-2015, 08:44
I know the entire solution to repair myself any kess pcb....and also can help you repair yourself.
All I need is a good pack of high resolution pictures with your kess motherboard so I will be able to identify problems.
Diode solution suck, it is a crap.....just a f++ing dead end, people.
Please use private message
franco75
21-01-2015, 11:37
vicius_the_one, tomorrow we'll place the picture of my PCB, I don't understand what you can serve or not there is a viable solution for everyone, each PCB has different problems?
Tomorrow I photograph my PCB, I do not understand what you can serve or not there is a viable solution for everyone, but each PCB has different problems?
vicius_the_one
21-01-2015, 11:44
As long As I cannot see real pictures of the PCB :
1. I do not trust you are a real customer in trouble;
2. I can see the problem.
3. The help only end user not merchants......they already did too many.....
vicius_the_one
21-01-2015, 13:21
Shut up man...this is bulshit solution..... buuuuulllllshshiiiiiittttttt. It really tricks nxp processor to enter the minimum speed!!!!!!!!!!!!!!!
there is how mine is working after child and adolescent psychotherapy and is have NO diode!!!!!!!!!!!!!!!! :
I said archive content is useless and contains no info.
Nothing more now.
Now let's come to our problems :
I solved 100% Kess(PCB China PCB Software 2.06 fake with FW 3.099) :
- k-line issue;
- WAKE UP ERROR;
- 24V issue;
- EDC17 Tricore.
Now let's go to the story that will make you stay.....first seat on your couch people :
Tricore read/write:
- micro
- flash
- eeprom
1. EDC17 CP14 - VW Touareg 3.0 TDI
vicius_the_one
21-01-2015, 13:22
Continuation
vicius_the_one
21-01-2015, 13:23
Continuation
2. EDC17 CP02 - BMW 3 2.0 TDI 177CP
And here is the **** proof people from EDC17 CP14 - VW Touareg 3.0 TDI:
http://youtu.be/nrTmzZq9xZo
I did not understand your problem, you continue to say that the solution of the diode ? wrong and that everything resolves otherwise, then post your solution and have done with it, instead of continuing to make statements, do you see how you will have to repair, and helps all.
franco75
21-01-2015, 16:20
I know that writes to increase the messages, he is not saying anything concrete
vicius_the_one
21-01-2015, 18:31
Nope man. I don't care about that. I just wanna say that many solutions proposed are dead ends..... Fake solution. I have reworked by myself kess and works as you can see. Only thing I say is this. I do not give solution for free because of the merchant whom I am mad on.... I just wanna help the end-users. Send me pictures with your pcb and I will help you....
clabsport
21-01-2015, 21:42
guys, in the meantime, I'll tell you what I noticed today, the software 2.06 on kess goes well and has some protocol in the pi? but it is only for the kess, in fact, I tried to do the same thing with the ktag, but the protocols that provide the edc16c39 and dense, are all disabled, I solved by putting the kessv 2.06 on xp and the ktag 1.89 on seven
I confirm what was said by Rodcraft86 on Ktag with version 2.06, some protocols are obscured.
clabsport
22-01-2015, 00:50
I just downloaded the V2 version.10 if any of you installed ? trusted? if we go off topic and tell me so that I open a new rear
? the same thing with the 2.10, if you use the firmware 3.99 you have the same protocols 2.06 nor more nor less, no ? the sw that matters, but the firmware that has the active protocols.
p.s. I have already tried the 2.10 in the network, all active, including boats and tractors, but they are all greyed out.
vicius_the_one
22-01-2015, 07:24
2.10 useless without fw 5.0
2.10 useless without fw 5.0
you've got to the kessv2 chinese?
vicius_the_one
22-01-2015, 08:23
I do not understand Who you are
I have 2.06 fw 3.099
clabsport
22-01-2015, 08:29
? the same thing with the 2.10, if you use the firmware 3.99 you have the same protocols 2.06 nor more nor less, no ? the sw that matters, but the firmware that has the active protocols.
p.s. I have already tried the 2.10 in the network, all active, including boats and tractors, but they are all greyed out.
I asked, thinking that updated the contact also firmware.
vicius_the_one
22-01-2015, 08:46
Exactly.... Once you don't have the appropriate fw... You cannot reach possibilities of 2.10 software
franco75
22-01-2015, 09:32
but the firmware ? updatable?
vicius_the_one
22-01-2015, 09:35
of course you can update it once you got it..
but the firmware ? updatable?
you need to have the firmware to upgrade the kess, unfortunately you will not find at a good price, and who do you reset the tool, but without giving you the firmware.
vicius_the_one
22-01-2015, 18:34
How nice would have been. :)
fabiovts88
22-01-2015, 18:46
hugo boss know from those who find the firmware? or give me a contact?
clabsport
22-01-2015, 20:27
But to update the firmware on the clon you have to do the welding and use the j-link how do I update the token or not?
I'm sorry fabio, but I don't know, I'm also looking for me, but do not c
vicius_the_one
25-01-2015, 22:12
i have 4.036 firmware....but in the process to decrypt an archive containing it....that takes time people......
matteo87
25-01-2015, 23:02
i have 4.036 firmware....but in the process to decrypt an archive containing it....that takes time people......
Have you original or clone?
vicius_the_one
25-01-2015, 23:22
Just fw and a clone that I will try to update...
fabiovts88
26-01-2015, 00:14
Just fw and a clone that I will try to update...
how ? can have this fw ?
vicius_the_one
27-01-2015, 21:00
you cannot mate. i practically have not it too. first i have to decrypt the archive and make tests. after that WE CAN TALK about having a good fw...
frantik3
27-01-2015, 21:43
vicius's Firmware!!!!!
vicius_the_one
27-01-2015, 21:51
:).....just wait for decryption
clabsport
28-01-2015, 13:51
vicius_the_one here as in other forums a lot of smoke and no fire will be? a case?
vicius_the_one
28-01-2015, 18:24
huh
Why? I judge ... I told the whole world that I am not interested to share the information to all, why? there are many people also use the information in commercial uses . the only help end-users!!!!!!!!!!!!!!!!
Then, think of us? you want ... I don't mind that
frantik3
30-01-2015, 12:31
By vicius's keep us up to date me very interested
vicius_the_one
31-01-2015, 12:18
I will surely do that to people :)
I the solution of vicius's I tried it and it goes great, much better than the diode. in addition, reading and writing become more fast..
I the solution of vicius's I tried it and it goes great, much better than the diode. in addition, reading and writing become more fast..
Which solution are you referring to?
rodcraft86
02-02-2015, 18:04
guys I did not understand the solution, you can give us a hand?
to be replaced some components. ? need to see the pcb, as not all of the mountain of the same components, in some should be replaced more stuff than others.
rodcraft86
02-02-2015, 18:18
ok, how do you understand it? you did it alone?
ok, how do you understand it? you did it alone?
in fact ? what I am trying to understand if there is a solution how do you know if who do not disclose, you lupo1 how you did it.
vicius_the_one
02-02-2015, 19:43
Rodcraft I saw your message and yes I will help you for sure. Use my ***** to send me pictures of your board at high resolution to figure out a solution for it.
rodcraft86
02-02-2015, 20:24
perfect, thanks a lot
franco75
02-02-2015, 22:30
I don't understand this discussion, the user vicius's send a ***** with the picture of the kess and he will respond on what to change?
Not ? out of regulation as well as a system a bit absurd
msport (exil77grande)
03-02-2015, 13:09
Rodcraft I saw your message and yes I will help you for sure. Use my ***** to send me pictures of your board at high resolution to figure out a solution for it.
in this forum, or posting things oeventualmente with a pass to give to the admin or post for everyone without a pass and download the ones that have the system, but nothing in private,I hope this is clear.
msport (exil77grande)
03-02-2015, 13:12
I don't understand this discussion, the user vicius's send a ***** with the picture of the kess and he will respond on what to change?
Not ? out of regulation as well as a system a bit absurd
exact and' absurd then, or will you give yourself a set and complied with the regulation, or start to take action,of course I do not speak for you.
vicius_the_one
03-02-2015, 18:49
I am sorry for inconvenience but my English knowledge is very low so since i cannot use ****** translate to understand you please be patient and understand me. i do not want to argue with anybody or break the rules on this forum. If you could use english i could be thankfull.
rodcraft86
03-02-2015, 21:27
I apologize me for the violation, not repeat it
msport (exil77grande)
04-02-2015, 13:02
ok guys calm I know that it was in good faith, but were more careful.
vicius_the_one
06-02-2015, 23:01
MAY i have your attention please.....EDC17 CP14 Write full Backup.....34 seconds !!!
Edc17 cp14 backup write - Record speed - YouTube http://youtu.be/wLTFX6OrzOE)
PS : the Final stage of rework !!!
MAY i have your attention please.....EDC17 CP14 Write full Backup.....34 seconds !!!
Edc17 cp14 backup write - Record speed - YouTube http://youtu.be/wLTFX6OrzOE)
PS : the Final stage of rework !!!
hello vicius's, can I ask you why in the video, the sw does not ask you never to turn on and turn off the key? you cut the video or do you have a sw that is different, thanks.
vicius_the_one
07-02-2015, 07:48
It's boot mode!
MAY i have your attention please.....EDC17 CP14 Write full Backup.....34 seconds !!!
Edc17 cp14 backup write - Record speed - YouTube http://youtu.be/wLTFX6OrzOE)
PS : the Final stage of rework !!!
edc17cp46 4 mb thee, the law from the serial port? The vag med 17.5.5 via serial? The pcr 2.1 vag simos via serial? The ford 115 hp 1.6 cc tdi simos 807 continental via serial?
vicius_the_one
07-02-2015, 14:51
It is only ecu i have.... Isn't enough?
MAY i have your attention please.....EDC17 CP14 Write full Backup.....34 seconds !!!
Edc17 cp14 backup write - Record speed - YouTube http://youtu.be/wLTFX6OrzOE)
PS : the Final stage of rework !!!
The movie EDC17 CP14 with modd file in 4 minutes !!! Ktag does in the same time !!! FLAWLESS !!! I thinks is enough wit this hardware...It act as a genuine tool!
then....I have to buy it but I don't know what and where...thanks
HI guys. Anyone solved completely clone...except me? I can help ypu also with 4..6
this change should be made in the same way for the kess v1?
frantik3
09-04-2015, 20:52
I think that kess 1 is different from kess 2
sorry, I do not know if the administrators allow it, can someone post a picture with the change of the diode for kess v1?
? already been posted here on the forum, in any discussion, in any case ? a palliative not ? the right solution, for it to work well you need to change several components of the pcb.
passion engines
13-04-2015, 00:21
now is the v4.036 is exact, it remains only to make the upgrade pcb.......
if your kess works without problems with the upgrade pcb not ? need
passion engines
13-04-2015, 11:07
you will find various fix around... if the board does not ? their poor quality is simply
if someone ? interested in the firmware v4, let me know..
now is the v4.036
where is it located?
you will find various fix around... if the board does not ? their poor quality is simply
if someone ? interested in the firmware v4, let me know..
passion engines
13-04-2015, 11:33
where is it located?in the network, quietly..........
the network is just crap and I know from experience! I'm interested in the updated firmware for kess
passion engines
13-04-2015, 11:49
if your kess works without problems with the upgrade pcb not ? need
and how do you know that it works without problems? you notice when you plant a unit in writing and, at that point ? too late, all of these tools have components of poor quality, the famous tools "european" are nothing more than the chinese with the upgrade to the pcb, at that point you can think about having a tool that has very few problems.
fabiovts88
13-04-2015, 13:49
you will find various fix around... if the board does not ? their poor quality is simply
if someone ? interested in the firmware v4, let me know..
I'm interested bimmer
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.