encoding pump audi a6 v6 155hp 0470506002

[special]

a greeting to all the forum I ask you experts if c'? the possibility? to encode a pump as the title of a audi a6 v6 tdi 155?

tests performed: procedure coding with vcds as in the manual but the pin is not correct
scodifica total ecu edc15vm without any result

the only solution ? go to audi?

thanks in advance

[blackwolf76]

I know that with kts bosch should be possible... but I never had the chance to try.

[legendaryslave]

with the total had to start spraying the liners ?

[tecnoracing]

you need to check the log with vcds you can do it easily

e-mail the reading of the 24c04

[special]

you need to check the log with vcds you can do it easily

e-mail the reading of the 24c04

? possible to get the login from the 24c04?

[special]

8414dump 24c04 edc15vm audi a6 2.5 v6

[mjet10]

Are you mounting a pump injection used?


You're mounting a pump injection used? if you're mounting a pump injection used to connect the plug on the old one, turn on the picture then remove the plug and re-mounting them on the new one... turn off and then back on, the car should start... I have done this several times.

Then today I had more time to try it, the map smokes only at 3000 rpm, but only if you stab the throttle, I think it's the fault of the injection times are too long in the wrong area you need to search for du to understand the logic

I was wrong to write I need to try to understand the logic

[special]

if you're mounting a pump injection used to connect the plug on the old one, turn on the framework, then remove the plug and re-mounting them on the new one... turn off and then back on, the car should start... I've done it several times.

hi thanks for the response, which is the pump I found in demolition I try this advice and you'll know, I also obtained the pin from the 24c04 hoping it is the right one

[tecnoracing]

your login and 03465 go with the vcds in access, enter the login and then adapted to the channel 50 save and exit power off and back on, the framework should be ok

[special]

your login and 03465 go with the vcds in access, enter the login and then adapted to the channel 50 save and exit power off and back on, the framework should be ok


at this time the ecu ? scodificata total bisonga bring it back to the original or ? can do with the vcds anyway?

with control unit scodificata total vcds does not accept the pin code 03465
now I put back everything the original ? try again


hi thanks for the response, which is the pump I found in demolition I try this advice and you'll know, I also obtained the pin from the 24c04 hoping it is the right one

tried this solution with control unit scodificata total ? does not work

c'? a particular procedure, why? with my vcds 912 I can not login with the 03465 I also tried to login with 34650 seems to accept it but it will block the communication until I turn off the ignition and the power back up

and can calculate the pin code to a 7-digit?

[tecnoracing]

before you go to access and enter 03465 and after adaptation on channel 50 check and save

[tezzero]

[special]

you should not have scodificare nothing...
the engine control unit ? been referred throughout as the original

any advice?

[special]

before you go to access and enter 03465 and after adaptation on channel 50 check and save

tried the procedure with vcds, but does not accept the login with 03465

I have to say that the engine control unit ? been reported to the original without scodifica.
any advice?

[tecnoracing]

at the end you did it? or no

[special]

at the end you did it? or no

No :-( I failed :-( then not sobil why? but administrators I have downgraded I don't even have permission to edit my profile I tried to contact them na no answer :-( I don't understand