problem mito 1.3 multijet

[francescosparco]

hi all.. I have a problem.,. use the rooster clone v50. I tried to read a alfa mito 1.3 mj, ecu data ok.. go on writing, and after a moment I get error contact the supplier.. what is? nn you read normally with the cock?

[Exelion1986]

hello sorry but you say you tried to read it but then you said you go on writing... the error you by the read or write?
anyway, with this obd ecu is read only in a virtual, try to go see it in the installation folder of the software, there should be a document with the list of all the cars
in particular, that the model of the ecu mounts on your side?

[francescosparco]

in fact, I was wrong to write.. I wanted to say I try to read it, and nn... I have read that it is in the virtual..but how to do it?

[Exelion1986]

do everything you normally, it's just that the file of the fishing from the database instead of reading it really
it could be that you get error why? not ? this file
check the driver list in the installation folder of the rooster and see if ? listed your car

[francescosparco]

here, then where? the problem..thanks

[Exelion1986]

no ? my guess... I'm not sure
however, you can always make it to the bench ? also pi? safe
the mountains are a 6f3 or a 8df?

[francescosparco]

I had read on a forum a similar thing . Anyway, if I do bench I don't know even from the dv start

[Exelion1986]

not ? a difficult thing, just a p? of manualit? and patience
in the software of the rooster, however, there are some excellent guides, and if you need a hand to ask
first of all, the procedure ? different depending on the version of the controller, the mountains, 6f3 or 8df

[Driver]

[francescosparco]

In this case.. there prover? . I really want to learn

[gianni1001]

sorry I'm intruding x,' I am also the owner of V54 clone
could you explain better how is the virtual read?
thank you very much:););)

[rodcraft86]

? a sort of virtual reading, it works so well?
the rooster has some file ori in the database of the software, when you go to identify and then read a marelli m6 or m8 he recognizes the ecu, and extracts from the database the corresponding file, the thing works in the first place if the rooster ? good workmanship and in the second place, if the file ori corresponding to the ecu ? in the database, basically it works as if it were a normal reading from serial port but it takes very little, the green progress bar is moving forward quickly and in the end save the file that is extracted

[francescosparco]

Sin to me, nn, and went

[ugoboss]

the virtual reading takes place on those ecu where not ? can do the reading from the obd, in that case, if the file ? in the database of the tool is the virtual read, but if you look at when selecting the car you say.

[rodcraft86]

exact, ugo has the right, at the bottom above the progress bar, it tells you if you make the virtual read

[francescosparco]

Nnt to me nn ago

[rodcraft86]

then either you don't have the file in memory, or it does not, the virtual read, but I think it is pi? likely the first hypothesis

[ugoboss]

then either you don't have the file in memory, or it does not, the virtual read, but I think it is pi? likely the first hypothesis

to me ? happened a couple of times that I had the file in memory and told me to open it and read it in the jtag (were 8df) and then send the file to them, very likely for an update of the database.

p.s. I have the v53 clone.

[francescosparco]

I v50 clone

[rodcraft86]

[gianni1001]

Maybe you can help me...I have to read a siemens EMS 3110/3150 CAN Megane 2000 RS turbo
the cock V54 not makes me read ,gets to 66% and then stops ...
suggestions?:)

[Driver]

Maybe it should open a new discussion, because here we are talking about virtual read on 1.3 mjt.

[gianni1001]

You're right Driver
Sorry I'm new just write in the forum and I have to get used not to change the subject...
And I need to better learn the rules
I
Thanks

[gick]

the problem ? that with a wingnut for example, my v52 seems to work really badly, how do you know if the cock is of good quality or not?

[Driver]

Cos'? that leads you to say that it's hurting your cock?