Immoff Gpunto

[blackwolf76]

I have a Gpunto 1.2 ecu iaw 5sf3 that they have lost the keys. Which would be the pi? indicated to proceed??

[legendaryslave]

since this ecu can not be made to total the most indicated to proceed according to my opinion ? take a reading of the body and proceed to create a new transponder or,- take body and keys to burglary and I recommend the same number to make the ecu partial ST10F280 through the reading of the ST10F280

[blackwolf76]

Ordering the key in fiat should not get already? working??

[Backgroop]

Ordering the key in fiat should not get already? working??

By ordering the key to get virgin the cost ? excessive around 130 a mechanical key, the key must be encoded in the fiat examiner or by other valid means if you have the code card

[blackwolf76]

And then they point and****.

[blackwolf76]

I can read with the cock 2 5sf3?? The scheme should be the same as the 5nf as documents of the cock??

[cinqueturbo]

I can read with the cock 2 5sf3?? The scheme should be the same as the 5nf as documents of the cock??

Diferenzia only A1 or M2.
8216

8217

[elettrocar78]

to make the scodifica total you should make a virgin ecu and mount cone e xxx, and simple mounts on the inside of the control unit, soldering, 4-wire

[blackwolf76]

Since I don't even have the keys to go into the demolition and seeking body with the framework, then will I do the part.

[obd75]

according to me the solution pi? comfortable ? sort the keys with the doorman how to solve?

[blackwolf76]

I have even change the door lock, as the owner does not want to pi? the old keys because I know the same ones that well as the thieves.

[rts]

sort the inpariglio again so you have the keys, and if the owner has the coupon code you are affixed....

[legendaryslave]

to fit a new key is always the old would otherwise not go ahead with the procedure better the way of the break-always the fastest and most econimica

[blackwolf76]

to burglary, I still have not found the complete appliance... not ? that if someone na has available a kit??

[blackwolf76]

I mounted all taken from demolition and I solved the problem. Only snag that I have left airbag light on, despite having done the alignment proxy, with error 8118 coding programming wrong. Possible solution??

[Senna_90]

I know that the bodycomputer has the crash of the drivers, you have to reset it in the microchip of the body

[blackwolf76]

The Cio? should I read the eeprom of the body and change that??

With the bosch I find no fault in the other systems if you are not in the drivers.

[glittering chiffon party dress.fitted]

I ask the colleague who has recommended the use of the emulator where I can find it thanks

[Senna_90]

[blackwolf76]

I open this discussion because I have a doubt about a car the same.

I have to riverginare a iaw 5sf3 m1 and the manual of the rooster brings me the two schemas that are posted just above, i.e., 5sf3 m2 and 5sf3 A1, being that changes the pinout and I do not wish to harm you, can you tell me which of the two to use for my??

Thanks

[cinqueturbo]

I open this discussion because I have a doubt about a car the same.

I have to riverginare a iaw 5sf3 m1 and the manual of the rooster brings me the two schemas that are posted just above, i.e., 5sf3 m2 and 5sf3 A1, being that changes the pinout and I do not wish to harm you, can you tell me which of the two to use for my??

Thanks

Simple compares The ECU with the images of the manual..
You'll notice that it also changes the color of the tab..

[francescosparco]

hello if you can affect, I have a controller in question is a virgin, never mounted that I must raise. you should only mount and take the code automatically if I'm not mistaken

[Backgroop]

hello if you can affect, I have a controller in question is a virgin, never mounted that I must raise. you should only mount and take the code automatically if I'm not mistaken

Hello If you are interested to sell your unit, insert in the section buy sell and add a link on this

[francescosparco]

Ok sorry...

[blackwolf76]

Indeed, the view look the same. However, I tried the steps m2 and should not be.

[Alessio93]

sorry, but c'? the appropriate interface for these units that does everything automatically !!! according to me it would be the best solution