Eurocargo tector - not by diagnosis

[rimec]

hi
I tried to enter the diagnosis on a eurocargo tector using autocom but the diagnosis does not turn on, seems to not receive power from the outlet. I checked the numbering of poles of the cable ? everything seems to be ok.
do you have any tips?

[passion engines]

Hello, have you checked your power supply??

[blackwolf76]

Adapter cables for autocom are worth and what iveco worst of all. If you want to do something, you have to modificartelo, to the limit and see if you recover a diagram partially functioning that should go on the tector.

[sisco]

hello try this system is always that you have the socket 30-pin round
obd autocom iveco 30pin
4-5 29
16 30
15 1
2 2

[klajdin]

Sisco but the K-Line into the Obd socket is switched on pin 2 of Autocom ?
I have made head of the tests but not sn never be able to do a diagnosis on Iveco, on any model...

[sisco]

hello klajdin I that configuration did not, in fact I tried it, (I found it on a forum where I was looking for the one for the scania 4 series that I found and it works)? the guy says that it works 100%, the user rimec I posted the pinouts for the edc why? he is not allowed to? still download attachments, you place an image that contains the link to the old truck and the new, then thou shalt make me to know if it works

[klajdin]

Thanks a lot sisco :) but I can't see it myself..

[giuseppeturbo]

Through the scheme, you should see in the meantime if c'? the power connector on the side eurocargo specifically positive and negative if you turn lautocom you are already on a good track then check the lines happened to me and with a bmw 728 of 2002 round connector, these machines can have two lines k and I had to modify the plug in the test or the moon or the other, in fact, that the chinese sockets are worth.

[sisco]

Thanks a lot sisco :) but I can't see it myself..
I can say that I purchased the cables for autocom chinese and I tried the cable 30-pin connector on an iveco stralis and it worked, I have not been to see what I could do in the ecu why? I was interested to see if the connection with the ecu was right because with the cock, I was not able to do even id data, when I go back in the workshop I take the cable and check it with the multimeter cos? I tell you how exactly ? wired. hello to soon

[nox]

Unfortunately the pin out 24 volts iveco, there are 2 types that carry power are wrong, and depending on the pin out that has your cable nn works for you safe n'? the cock, the autocom see if these will help one

[rimec]

hello to all
can't I see the images but I think I understand. do I get another cable iveco cut it and I look for the power supply and the poles to operate the diagnosis via the k-line.

[giuseppeturbo]

According to me, you don't need to cut just open up the connector and see if the connections are wrong and then make the necessary changes and that is it.

[sisco]

hello to all
can't I see the images but I think I understand. do I get another cable iveco cut it and I look for the power supply and the poles to operate the diagnosis via the k-line.


30-pin obd autocom
1 = 15
2 = 2
3 = 15
4 = 6
5-7-17 = 15
6 = 10
8 = 14
10 = 15
8 = 13
12 = 2
18 = 7
22 = 12
21 = 11
29 = 4+5 = ground
30 = 16 = v+
hello this ? the configuration that I posted a few posts above that you can not see this ? for the new truck, the old truck will change the mass instead of the pin 29 ? on the pin 30 and the positive instead of the 30 ? on the 27th, I hope that when the place does not change the text as I have written before you send the post, then if you have a p? patience tomorrow in the evening, I say to you, how ? wired the one with which I entered into the eoc stralis

[blackwolf76]

With that configuration, go in anything except the eoc... For the engine communicates on the k-line and pin 1/1

[sisco]

hello blackwolf76 I said, I have not tested, but that gave 100%, tomorrow check the cable that works and that I have personally tried it, probably will be? wired as you say since you seem sure of what you say

[blackwolf76]

In fact I have done quite a bit of testing with those cables and I can tell you that a cable is fully functional for all the iveco 30 pin does not exist... it takes at least a couple to be able to cover all of this in the way just decent.

[rimec]

.....I don't understand how to make the workshops....have a single cable. Maybe the problem is the diagnosis, the connection varies from diagnosis to diagnosis....

[blackwolf76]

The problem is the diagnosis farlocche and cables worse than the diagnosis. Obvious that with equipment official is not a problem...

[klajdin]

When changing the pin of the power supply, the mux should change the links internally via the rel?, same thing for the data lines. Autocom ? gi? so if it fails to connect ( I mean clone ), then the limit of using 2 different cables.., I of the cables 30-pin I picked up 2 but none of the two works. Now with the calm I feel the scheme sisco.

[nox]

I have the diagnosis truck cojali jaltest and does it all automatically with only one cable, however, on eurocargo stralis and new, you'll find a plug to the obd inside the fusibiliera passenger side

[sisco]

guys, I apologize to all but I forgot to bring home the cable to check like ? wired (? been a full day) tomorrow bring? not to forget about it

[sisco]

obd 30pin

1 = 1
2 = 2
3 = 3
4 = 30
5 =
6 = 4
7 = 15-17
8 = 16
9 = 5-7-9
10 = 6
11 = 21
12 = 22
13 = 8
14 = 12-14
15 = 10-18
16 = 27
hello guys, tonight I brought home the cable and the one above ? the configuration of the pins on the cable c'? an adhesive label with a written " iveco 30p v2", I think that means version 2, however, I with this cable are entered in the edc stralis 360 (but only edc), the rest I have tried, I have used autocom to a gold version 2013-1, if you try and it works please tell (me captain a few iveco)
greetings Sisco

[hyrosat]

Hi guys, sorry but I also have the same problem autocom clone on iveco nothing to do with either 30-pin 38-pin, how could I solve it? I changed 2 cables, but nothing with none of the two, now I wanted to remove the cable to see the links but ? everything is closed what can I do? you have a few photos to try to solve the problem?.

Thanks