Spy ESP on Mercedes C200CDI W204 after mapping

[magi1984]

Hello guys, I present the problem.
last week I mapped a Mercedes C200CDI W204 136cv Delphi.
a week later the client says that at 150km/h the indicator light is on esp and says that ? the fault of the mapping
to me it seems impossible, today, to put back the original machine and I try the original to see if it is actually original to the car ? ok.
do you think it could be a problem of the map?
I doubt it strongly.
in the case I'm attaching, however, the map ori and mod to have an opinion.

:)

[msport (exil77grande)]

I have not seen the map but I guarantee you that it will be a case,however, test the file ori.

[cawadany]

I'll maybe try to make a diagnosis...

[magi1984]

the second ? put the original to show to the customer that the map is not centered (according to me) and give him the sop

[freddyecu]

also I think the map has nothing to do with esp and then to the other, the ecu the engine is not gesticce esp... but once people mappatala machine always try to blame it on the mapping...I would try to make a diagnosis... but the light and turned on or fixed lights soloa speed greater than 150km?remember also that if you write to the ecu via the serial sometimes you store the fault codes to the control units type esp, abs ,body computer etc because write is interrupted, the communication between the ecu and the rest of the control units...could this be the problem ....it would be enough then a reset

[giarras]

make a diagnosis as you have suggested, I looked at the file, I don't think depends on the changes that you have made anyway you can always put back the gold and try both to be sure.

[blackwolf76]

Mercedes-benz is sometimes catch errors from the sun... and then just switch off and remove the key to reset them by and leave.

Anyway, since the problem 10 to 1, which has a wheel sensor that is not working well. Loses the signal from the crankshaft speed? you indicated, even if many times in those cars, if they have a number of MILES, should be recorded on the wheel bearings in the front, and that by purchasing the game due to wear, remove the sensor from the crankshaft enough to make him lose the signal.

[freddyecu]

What do you mean, that shall be recorded the bearings in the front? In that way? I thank you in advance

[blackwolf76]

The wheel bearings on the front of the mercedes are of the cone type, or of the type that had the old cars, like the mythical 500. Then running out strong, then you loose again and tightens about 1/4 turn beyond what we can tighten it by hand. of course with the wheel raised goes this is all done and you have to make sure that you do not have the game.

[freddyecu]

So in the case of recording just loosen them and tighten them again?

[blackwolf76]

So in the case of recording just loosen them and tighten them again?

if they are not noisy, just record them...

[klajdin]

once I ? happened the machine lit the lamp x because of the convergence, I know that maybe it seems unlikely, but the fact of the convergence without touching the other everything is ok, but in this case, from the diagnosis, you should see it

[magi1984]

the car ? back and had 8 faults in the memory
4 in the engine and 4 in esp. of these 8 errors, one referring to the torque motor, all the other 7 are network failures can
therefore, I believe that the problem lies precisely in the map.

for now, the client runs with the car original, to see if this is what the defect.
in the meantime I I adjusted the map by placing a torque limiter, and if I'm not mistaken I found a nth limiter off driver

[gfr]

I would try to cambiagli the iterrutore stop the pedal, and the pair if and high abbassala

[cicciogsr]

the car has the automatic transmission?

[magi1984]

the currency exchange ? automatic

[cicciogsr]

if ori does not f? ... recheck all the maps that are regulate the torque... a question why? the last curves of the times you didn't mod?

[magi1984]

for my wrong belief, was in order to not clog the dpf,I was convinced that at the top was better to leave it original. :)
now I can fix it, thanks for telling me! I don't remember pi?!

[msport (exil77grande)]

I advise you to check the motor and butterflies three suction.

[tecnoracing]

msport but if there was a problem to the butterflies had to find the error in diagnosis

[tecnoracing]

happened to me and on a bmw 535 a similar problem and it was the map that was a little push and the automatic transmission that wax some parcel clutches that did not resist and went recoveri transmission problems

[magi1984]

the problem ? fixed redoing the torque limiters in the map.
probably one of them ? been raised enough and arrived at 150kn/h lit the lamp, and the car you drove in
I test them I have increased all at 30%, and the problem ? gone.
I would have liked to try them all one by one to understand what was the limiter bastard, but I have had the opportunity why? the customer ? come to take the car

[cicciogsr]

I had taken then!?... if it had the automatic transmission, perhaps, would not have happened

[magi1984]

gi?, I think so!

[rodcraft86]

guys I reconnect to this post for a problem identical to the one described above, the drive ? mercedes c220 cdi 2008 170cv delphi dcm 3.2 ? been mapped, but over 2800 rpm crashes and goes into recovery with esp light on and message on the display, moreover, the first map I could diagnose it with autocom and now I can not do more? nothing, you know what can? be?

[sportknight]

the writing ? come to a good end? checksum ok?

[rodcraft86]

everything is ok, the car drives strong up to 2800 then if you keep it below has some hesitation and then it cuts to the shot and makes the 80kmh, if you turn off and back on, everything is normal

[cinqueturbo]

everything is ok, the car drives strong up to 2800 then if you keep it below has some hesitation and then it cuts to the shot and makes the 80kmh, if you turn off and back on, everything is normal

Mail file ori and mod..
don't forget to place the file ori in the appropriate section if it is not already,
pasting here the link..

[rodcraft86]

here are the files guys, I hope I can resolve with your aiuto7742

[rodcraft86]

I update that was autocom does not work and does not map to impedigli access to the unit?, I don't understand the reason why? delphi updated to 2013.3 works great comes everywhere

[rodcraft86]

guys do not c'? anyone that can? give me even just a advice on how to proceed?

[fire]

you have then solved rodcraft?